Yes! It is necessary to know the diameters to be connected and to define whether the pipes to be connected together have a socket or otherwise.

Unfortunately, most plumbing stores don't carry HDPE - often times the store employees have never even heard of it. Usually it can only be found at large industrial plumbing supply places. You can also purchased pre-cut, plugged pieces of HDPE pipe from Pyrogear.net, which specializes in making mortars for fireworks. See similar questions...

Definitive Sealing: by welding the Valsir sealing cover (art. 342). Non-definitive sealing: solution A: by welding the Valsir sealing cap (art. 340). Solution B: by welding the Valsir collar (art. 347) then, using the Valsir free flange (art. .45), the corresponding set of Valsir bolts (art. 341), the Valsir sealing gasket (art. 343) and the Valsir blind flange (art. 346). See similar questions...

Water pipes are made in many different sizes and design. On top of each pipe you'll find a bowl in which you can place your favourite smoking blend. When lit, the smoke is drawn through water before reaching your mouth and lungs. The water has an important filter effect. A large part of carcinogens like tar are filtered by the water. In addition, the water cools the hot smoke and the protecting mucous membrane of the lungs will be less harmed. See similar questions...

The UNI EN 1519-1 standard only refers to HDPE pipes and fittings for waste systems inside buildings, however the raw material is the same material used to manufacture pressurised HDPE to transport H2O. See similar questions...

ASTM F679: Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings ASTM F789: Standard Specifications for Type PS-46 and Type PS-115 Poly(Vinyl Chloride) (PVC) Plastic Gravity Flow Sewer Pipe and Fittings ASTM F794: Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter ASTM F949: Standard Specification for Poly(Vinyl Chloride) (PVC) Corrugated Sewer Pipe With a Smooth . See similar questions...

Our hovercraft are designed to float like a boat with the engine turned off. Hovercraft make excellent diving tenders and superb hunting and fishing platforms. See similar questions...

High Density Poly Ethene but most commonly known as Polythene. One of the most common plastics you use in daily life it has an oily-type finish. Some of the original Prototype Stunt Stormtrooper Helmets were made in HDPE as Andrew Ainsworth (the original maker of the helmets) had some of this plastic in stock as he was making Garden ware and Fishponds. It was a khaki-coloured plastic and due to its oily nature it was a bit of a struggle getting the white paint to stick to it. See similar questions...

There are few areas of the South Platte River that are good floats in our district due to the shallow river depth and/or rapids and there are several areas along the river that are privately owned. By Colorado law, these property owners can restrict access the the portion of the river than runs through their property. For those desiring to float the river it is important that they check the depth and current of the river in the area they choose and be aware of any property restrictions. See similar questions...

The term ''float variable'' is actually redundant; they are simply variables whose value can ''float'' during execution. For instance: float f, g = 3; f = g; /* f ''floats'' to g */ See similar questions...

Firstly this situation is not unusual because after each time the airconditioner dumps water with its water management system there will be a period of drips until the pipe clears. Also after its rains you may see water dripping from the drain pipe, however, if it continuously drips and is of concern then you should contact your service company or Seeley International on 1300 650 644 to book a service call. See similar questions...

If the run from the house to the street is short (under 60 feet) I'd use *Type L * soft copper. It is less likely to break and it has no fittings in the ground except at each end of the pipe. I'd also put pipe (foam) insulation) around the copper run. For longer runs my next choice would be schedule 40 PVC pipe. Not a bad choice at all. I would not use flexible plastic - that is black *poly* pipe. It comes in a roll. See similar questions...

After a Lock-In, if rates are reduced, some lenders will allow a borrower to choose the lower rate at closing; however, this usually requires a fee. See similar questions...

Biomatrix gold has been wave tested and will float without hydrocarbons for a period of 72 hrs or more. The ability to remain afloat for a long period is an affirmation of the quality and concentration of barrel cells-now filled with oxygen, proving its superiority. See similar questions...

HDPE is a translucent white colour in its initial state. A small quantity of carbon black is then added to protect the product from ultraviolet rays. The UNI EN 1519-1 standards at the heading: "Colour", establish that it shall be "preferably coloured black". See similar questions...

Yes, the Town of Apex has a leak adjustment policy to help customer with major leaks. A copy of your plumber's bill showing proof that repairs have been made should be submitted to the Utilities and Finance Department at P. O. Box 250, Apex, NC 27502. The Town will adjust up to two month’s billing for leaks that are more than 50% of the customer’s average water bill. Adjustments are applied as credits to the utility account. See similar questions...

The principle of water cooling is using water as the heat dissipating media. It is good not only at dissipating heat, but also on the circulation flow inside the chassis. Heat pipe cooling, however, uses air as the media of cooling. This works especially well on CPU cooling, but may not as effective at circulation flow inside the chassis as water cooling. Fans are major components in this type of cooling. It is important that the fans are securely fastened to prevent vibration. See similar questions...

Water District Personnel will inspect the condition of the pipe before installing the new meter. If the condition of the pipe is uncertain, we will not be able to install the meter. According to the District's Rules and Regulations, the property owner is responsible for the maintenance of the service pipe on the property. See similar questions...

Careful selection of the components practically prevents the possibility of a pipe breaking. Should a leak nevertheless occur in the cooling water system in the rack, the positioning of all water-carrying parts on the lowest level of the rack ensures that water can never reach above this level in the server. A water sensor is also offered as an option, with which even the smallest leaks can be detected immediately. See similar questions...