Go to the Computer Labs Homepage at http://appl003.lsu.edu/ocsweb/palhome.nsf/index or select it from the A-Z link under the main LSU homepage http://www.lsu.edu. Click on the link at the bottom right under the paragraph beginning with "Wireless Printing now available" or goto the following page located at http://lsu-tut/index.htm. Select "Middleton Labs" from the map. Decide which printer the job should be sent to and click on that icon.

Yes, as long as the laptop meets the minimum computer system requirements. The laptop must also have a PCMCIA Network Adapter installed.

Mobile Computing is on a new system called Cisco Clean Access. For more information go to Get Connected. [top]

MaxiVista is a must if you have two or more computers sitting on your desktop but it is not of help Iif you have only one single computer. The main benefit of MaxiVista is that it allows you to use a computer as a monitor. Learn more here how MaxiVista works

There are several possible reasons why. One may be that you must use either a cross over cable or have a hub between them; a second may be that the IP addressing of the 6000 and your computer may be on different networks and therefore cannot talk. Commonly (with a subnet mask of 255.255.255.0) the first 3 sets are the network e.g. 192.161.111 and the last e.g. 222 is the node so if the 6000 series had a fixed address of 192.161.111.222 then the laptop would need an address of 192.161.111.

That depends of what you want to do. If you want to send e-mails or go on the Internet, you have to connect the PC/Laptop to the data port of the mini-M (use a straight line serial cable RS 232) and then you will be using the build-in modem in the mini-M. Whereas if you want to send faxes from the PC/Laptop, you have to connect a modem to the PC/Laptop and connect the 2-wire cable to the AUX/fax port of the mini-M.

Find the access number or numbers you want to use-then download the file and save it to a disk the file is small so it can be saved onto a floppy disk, cd or even sent via email Then just open the file on your new computer and it will automatically configure your dial up connection the manual set up instructions which will walk you through step by step (with pictures) how to set up the dial up connection. MANUAL SET UP

You are expected to keep daily notes on the project, weather and wildlife sightings. There will be a project notebook on the island, as well as copies of notes and sightings from previous years.

No. All new students will receive their laptops at an orientation session to ensure that everyone receives complete information about the computer, including its warranty, insurance coverage, software usage and Rose-Hulman's policy regarding the responsible and ethical use of computers.

Simply contact your Property Manager. They will provide you with all the information you need, and will get you set up using ServiceLink.

The 60 gb model has built in WiFi. So you will receive internet signals instantly. Supports 802.11b and g. Data rates 11mbps and 54mbps. Will it support Super G? It doesn’t look like that is happening at launch. Remember, you will still need to have an internet connection thru a wireless router and/or modem.

SP918 is a typical Access Point which means SP918 is used to coordinate traffic between wired and wireless LAN. Wireless Adapter (like SP905A, SP906A, SP907A) could be linked to Ethernet through SP918. If you needed Access Points that could communicate with each other wirelessly, that means you want to connect two LANs. In that case, what you need is SP912. SP912 is a Access Point with additional "Bridge" function. Users can connect two or more LANs together with bridge function.

Information travels from a secured Internet location directly to each authorized users computer through radio frequency waves.

Yes, while there are problems being experienced by other companies, all data transmitted wirelessly through SkyeWired it is very secure.

Two or more computers can connect to each other using NetBlaster II technology by peer to peer (Ad Hoc mode), or via the wireless Hub (Infrastructure mode). Peer to peer uses only wireless Adapter cards to connect each computer. A wireless Hub connects these computers, and then allows connection to a wired Ethernet network and/or a Broadband modem for Internet access.