Even though the lumber may be kiln-dried before treatment, using water-borne preservatives restores moisture to the wood. Too much moisture in the wood may prevent the stain or paint from penetrating the wood sufficiently. It is best to test the wood by painting or staining a scrap piece to see if it applies properly. If not, wait until it does. A water repellent should be applied annually. Do not use latex paints. Semi-transparent, oil-based stains work best.

Ans: The insulating additive will help keep the deck cooler while providing a slightly slip resistant surface.

You should certainly protect your deck from unnecessary moisture intrusion and the harmful effects of the sun's ultra-violet rays. Use of a penetrating stain, containing water repellant ingredients in most cases will protect your deck best. The pigment in the stain will absorb the ultra-violet rays from the sun and protect the wood fibers from degradation. In most cases a stain will need maintenance every 2-4 years while clear sealers require maintenance every 1-2 years.

We suggest allowing the wood to weather naturally for at least 3 to 6 months before considering paint or stain.

Typically, all wood fence should not be stained or painted until a minimum of 60 days after installation. We recommend you check with your local paint store for the proper method of application.

On a horizontal surface, Penofin may be expected to perform for an average of 9-18 months and 3-5 years on a vertical surface. The time will vary depending on the percentage of sunlight, weather, etc... Yes. All Penofin wood finish colors contain the same ingredients, just different amounts of colored pigments. However, you will not be able to make the surface lighter by applying a lighter shade. As always, you should test a small area before use.

The product does not require traditional timber treatments or any other kind of treatment BUT it will of course require normal cleaning with a pressure washer or hose/brush with a weak bleach solution or proprietary deck cleaning product to remove surface debris.

I prefer to use a large brush or a mop. You want to get large amounts of Stain Solver liquid on the deck surface. Hand pump sprayers often apply too little solution to the surface. If you must use a sprayer, make sure the product has dissolved completely or you will clog the nozzle! Also, be sure you spray on lots of liquid.

We recommend that your siding have a moisture content of 15% or below prior to staining. Since many homeowners do not have access to a moisture meter it is a good recommendation to wait 3-5 days after a heavy rain to allow the exterior and interior moisture content of the wood to lower. After the home has been thoroughly cleaned using Cabot Problem-Solver Wood Cleaner and the coating is in good sound condition, we recommend using Problem-Solver Oil Primer.

Answer: The insulating additive will help keep the deck cooler while providing a slightly slip resistant surface.

The available historical evidence shows that Eichler used stains, not paint, on his homes, inside and out. One can speculate that, at least for the vertical-grooved siding, stains were employed so that the grooves stayed crisp and clean (the edges weren't softened by the paint), and some of the grain of the wood showed through (redwood siding was used throughout the 1950s). It is also possible that Eichler used stains because labor and materials costs were lower than for paint.

We do offer "certain styles of pre-primed balusters" but we do not do any painting or staining of any kind.

Jennings joinery prefers to paint or stain prior to glazing and assembly to properly seal the product. Also when using 6.38 Laminated glass (which is thicker than normal glass), if the inside rebate is not painted or stained prior to glazing then after the product is glazed the unsealed surface behind the glass edge is visible and un protected. Also after the bi-folds have been installed it is very difficult to coat the top and bottom of the doors to seal then correctly.

When you're looking for a painted-kind-of-look to match you home exterior, or when the deck has been totally neglected, solid stains hide and conceal any cosmetic imperfections that the lumber may have.

Dry time to apply the second coat will be approximately 2-4 hours. Dry time to use a deck will be approximately 48 hours. Maximum cure and dry time may be prolonged when high humid or damp, cool conditions prevail.

The average waiting time in New England for a liver is about 2 to 2 1/2 years (but it can range from weeks to years).

While drying times can vary based on factors such as humidity, plan on waiting about four hours when you are using latex paint. If you are using oil-based paint, you will probably need to wait up to 24 hours.

Aesthetics: Clearly the outside of your home is a great source of pride. Having a manicured lawn and beautiful, clean deck allow for a great outdoor living experience. Entertaining, cook outs with family and friends on clean, protected surfaces create joyful memories that last for years to come. The best way you can protect your deck is power wash cleaning and professionally applied protection products.

All of our products are high end. Certain products will do better then others depending on your particular environment or type of wood that you have. If you came to our store looking for a certain brand name then we would suggest sticking with that. Please email us if you have any questions and we will be more then happy to suggest a certain brand depending on your situation.

That's an opinion call, but if you do, you will have to do it again every year. We recommend letting it grey naturally and washing it 2 or 3 times/year with Sunlight dishwashing soap to keep it clean and pollution-free.