WE are a large Healthcare organization in North Carolina. We acquired a 300 unit (apartment) Retirement Community in the alst few years. We need to upgrade and replace all of the "through the wall" units that serve each apartment (square footage varies from 480 sq.ft. to 1400 sq.ft. Magic Pak heat pumps (12000 BTU, 18000 BTU/ 24000 BTU- according to size of area) are being suggested for replacement. I am looking for an opinion on these units- good, bad or indifferent.

That depends on the size and style of the home as well as the materials and finishes chosen. As an example, did you know that a single-level home generally costs more per square foot to construct than a multi-story house? Also, the cost per square foot decreases as the size of the home increases. As a guide for preliminary budgeting purposes, the typical custom home usually costs somewhere between $120 to $195 per square foot to construct. (back to top)

I have a free standing 24x24 feet garage with 9 1/2 foot ceilings. What btu should the heater have to heat this space. I live on the illinois/wisconsin boarder. winters damn cold thx mike

This is by far the most asked question and the most difficult to answer. There are just too many variables. A simple rectangular home without many interior log walls would be considerably less per square foot for a similar size home with interior log walls, additional corners, stairs and handrails, etc.

The EQ-300 whole house water filter system is 45" tall and 9" in diameter at the base. It requires a total line length of 24" for proper installation of the prefilter and the ball valve assembly. The filter unit comes in two packages, weighing 53 lbs and 6 lbs, respectively.

The foot length should be kept as short as possible. For a firm load (such as a box) it does not need to be as deep, for a softer load (a sack) the foot must fully support the load.

I'm looking to heat and cool and old theater with no existing system. It is approximately 10,000 sq. ft. and goes from aproximately 20 ft. high in the rear to 40 feet high in the front. It will seat approximately 300 - 400 persons. How many ton system(s) would I need and what kind of system would you suggest? Also could you guesstimate a cost for the unit(s)? THANKS Hello, I have a 5 ton AC unit for my 2100 sf ranch home in Phoenix, Arizona.

Equals a square 12 inches on each side and can be any thickness. It is typically used to measure engineered panel products that are less than 1" thick, including plywood, particleboard, medium density fiberboard and oriented strand board.

The AC cannot be installed until your home has electricity. Notify the service department when your home has electricity, and the installer will come and install your AC unit. (Cost for installation is covered)

Ask us. We will consider many factors before making a recommendation. Factors like ... size of the house, climate, the number and type of windows installed, and insulation in the house.

We recommend 2 because we have found that both feet are typically weak and both should be exercised. You can exercise both feet at the same time so it is twice as fast and you are able to compare the strength and flexibility of both feet. We sell 1 to make it affordable for everyone. You can perform most of the exercises with 1 Foot Trainer, it just takes longer.

All size engines are catered for from outboards to super yachts. Unit size depends on your fuel supply lines. If you are unsure what size your vessels feed is, measure it or contact us. The standard unit is for fuel supplies up to 10mm, (3/8’’) fuel feed. The unit measures L=160mm x W=50mm x D100mm. For smaller or larger sizes see our product range or contact us for bespoke units.

To figure out the best unit size for your need please check out our What fits in your space feature. This feature will help you in determining the right size unit for your specific need.

The estimated sq. footage is approximately 1,200 sq. ft. Both Villas include 2 bathrooms, 2 bedrooms, living room, den, dining room, a fully equipped kitchen, and a patio with barbeque & ocean views.

Every project is different. In order to generate your quote, many factors need to be taken into account. However, by contacting our friendly technical team we can quickly provide you with a detailed estimate.

No. Every project is different with the prices varying according to project type, medium, difficulty of installation, etc. We encourage you to call for pricing information. You can not put a square foot price on art. It is not wall or floor covering. It is for the most part a permanent fixture that expresses not only the personality of the artist but of the owners for which it was designed. We can provide estimates, but only after we have the answers to certain questions.

Pricing houses by the square foot is like pricing cars by the pound. It is not a good measurement of “what you get,” and usually is not a guarantee of anything. Because we are a custom homebuilder and serve a wide geographical region, we do not price our houses by the square foot. Your cost per square foot will vary largely based on three factors: The total square footage (larger homes = lower cost per square foot) and the features you design into your home.

When you order from our web site you input numbers of tiles that you want. The prices are specified next to the pictures by both tiles and by sq. ft. Each tile is 2.69sqft.