This message is coming directly from the SMTP server and it is letting you know that you are not allowed to send messages through it from your current network location. SMTP servers can be configured to send messages for anyone that connects to them, but this is rarely the case in the real world. Due to the SMTP abuse by spammers and mass-mailers, the network administrators had to close their SMTP servers to only allow their clients to send mail.

DLS dialup customers should use mail.dls.net as the SMTP (outgoing) and POP3 (incoming) mail servers. For DLS web hosting customers, please see question 3.1. If you are dialing up outside of the Chicagoland area, you must use a mail client that supports SMTP authentication (such as Outlook Express or Netscape Messenger) and configure it to use the same settings as for POP3. For example, if your email address was joe@dls.net, you would use joe as the username for POP3 and for SMTP authentication.

Be sure to CHECK your mail via POP3 first. Due to widespread Internet SPAM abuse, we are unable to operate an "open relay" that would allow anyone to send mail from our server. As such, we use what's called "POP Authentication based selective relaying". When you authenticate via POP3, your IP address is added to a list of IP addresses that are temporarily allowed to relay through us without restrictions.

There are two things that can cause this error. The first is that you have not logged in and checked your email within the past 20 minutes so your IP has not been given SMTP access. The 2nd is the program on the server that logs IP's for SMTP access has died. If you believe its the 2nd of the two, send in a ticket and we'll get things straightened out right away.

We do not allow clients to use our server for outgoing mail for security and spamming protection. When you try to use mail.domain.com as your SMTP server, it will respond with an error. The fix is to use your ISP's SMTP server. Most ISPs use smtp.isp.dom as the outgoing server.

This is probably because you set up your mail client to use ValueWeb's mail server to send mail via SMTP. Due to problems with spam being routed through ValueWeb's mail server, you must now use your internet service provider's mail server to send outgoing mail.

In order to successfully send mail through Access 1 mail servers your email client must pass your username and password before email is sent. The following instructions will instruct you on how to configure Outlook Express.

Our system is designed to work with SMTP authentication (enabling instructions below). We do however have a backup system that may take up to one minute to enable mail delivery without SMTP authentication causing the 'Relaying Denied' error. Subsequent attempts should result in successful mail delivery.

Our Outgoing (SMTP) mail server requires some kind of authentication of who you are, to ensure only authorised users can use our mail server. This error message means you have not authenticated. There are two ways of authenticating. When you download mail, you then have a window of a few minutes to send e-mail using our SMTP server provided you do not disconnect from the internet in between. In Outlook Express, the "Send and Receive" button does this the other way around.

If you wish to only provide data (of the hosts that your DenyHosts daemon has blocked) to the denyhosts.net server but not receive hosts that have been denied by others you can set your SYNC_DOWNLOAD to no. The default is yes but only applies if synchronization mode has been enabled.

The email server is not allowing you to send mail because it does not recognize your IP address. You are likely not connected to Grande directly, but rather (a) dialed into another provider, (b) at your office, or (c) travelling. Simply CHECK your email before attempting to send. This will permit your current location to send email for a period of 30 minutes. Each time you successfully check your email, your full 30 minute 'send window' will be refreshed.

It is an unfortunate circumstance that the "From" header of an e-mail message is so easily faked that it is usually not reliable in tracing its true source. (See below for more information about this.) However, spammers often forge the "To" header of an e-mail message, which is an attempt to confuse the true recipient of the message.

In order for HER v3 to do backups directly to your CD, the CD must be formatted "as a drive letter". This formatting is called "Drive Letter Access" or "DLA". But you may say, "I can see drive letter 'D' (or whatever) when I use Windows Explorer to view my CD drive". OK, but what you are seeing is the drive letter of the CD DRIVE -- not necessarily the letter OF THE CD itself.

You may get the following messages regarding the permission to trade on Comdaq. The messages and answers are as follows : You or the company you have registered to has not been approved or have been denied permission to trade on the system. a) You have had a change of employment and your records are still associated with your old company. If you wish to update your details and register your new company please contact us.

A common reason for a tag being denied is the POR and POD on the tag does not match the POR/POD on the OASIS TSR. If using the OATI E-Tag sytem, the system will show the reason why a tag is getting denied. Check the OASIS TSR to see if the POR & POD matches the tag. Below is a screen shot of the OATi E-Tag system showing the reason for a tag being denied. The POR & POD on the tag must match the POR & POD listed on the OASIS TSR.

The most common reason for this error is that your session is crossing domain boundaries (e.g., accesses a page from http://domain1 and then accesses a page from http://domain2), something which browsers generally do not allow JavaScript code to do; since the in-browser part of selenium is implemented using JavaScript, this leads the browser to complain. Note that changing protocols constitutes a domain change, e.g. going from http://domainX to https://domainX is not normally allowed.

You can select the "Local User Only" option in the Options dialogue. If this option is selected, only the local user can use Mail Direct as an SMTP server. Connections from other machines will be rejected.

Make sure that you are using smtp-yourdomain.com as your Outgoing Mail Server and your "From Email-id" is yourname@yourdomain.com. Every bounced message contains an error message, which is normally a self explanatory one. If an error has come from any of FutureNet Technologies's Mail Server, it will contain the name of that server with extension futurenettechnologies.com (e.g. pop1.futurenettechnologies.com, smtp2.futurenettechnologies.com).

There is currently no postal or e-mail address for sending fan mail to the cast or producers of Monk. No. If any merchandise is created in the future, information on what's available and how to get it will be posted on this site.