Our Roll-Up Doors are attached to the wood guide rails which are part of the door package, and require support of vertical walls.

The Garage Door Screen is mounted (in front of the doorstop, one-inch wood strips) on the header and the doorjambs which the garage door is mounted to.

Yes, the screen frame is offset to compensate for this. The adjusting screws for the screen wheels need to be facing the interior of the house. If the screen is installed‘backwards’ then the handle hits the patio door.

The Fire Rock system requires the same type of support that would be used in the construction of a brick and mortar fireplace due to the finished weight of the product. Fire Rock requires a non-combustible base. If built over a basement or crawl space, this can be accomplished either using concrete blocks or steel columns that would support a concrete pad typically poured by your installer. If Fire Rock is being installed on an existing slab, it requires a twelve-inch footing.

The type of evidence required will depend on the size and nature of the community. See Policy 2a Guideline2a)ii

This is the width of the space that an overhead door will need to cover. If you provide us with the TODCO serial number, we have the opening width of your door on file. If the serial number is not available, please provide the actual measurements of the width of your trailer, from the left inside wall to the right inside wall (post to post), along with the name of the manufacturer of your truck body or trailer, and the year it was made.

This is the height of the space that an overhead door will need to cover. If you provide us with the TODCO serial number, we have the opening height of your door on file. If the serial number is not available, please provide us with two actual measurements: 1) the height of your trailer, from the inside floor to the inside ceiling, and 2) the distance from the inside floor sill to the underside of the header.

There are numerous educational training programs available to would cardiac sonographers. There are Bachelors Degrees from university base four-year programs, Associate Degrees from two-year community college base programs, and some one to two year training certificate programs.

To achieve a single access door you would require an odd number of panels to stack in one direction i.e. 3, 5 or 7, etc or to split the stacking to both sides in order to achieve an odd number configuration to at least on side, i.e. 2:1, 5:1, 5:3 etc. To achieve a French door opening, you would require an odd number configuration to both sides, i.e. 1:3, 3:3, 7:3, etc.

Our door opener can be fitted to the majority of both internal and external hinged doors in a domestic and light commercial environment.

We are open Mon-Fri 9am-5.30pm. Unfortunately we do not work weekends and bank holidays. If you need to contact us outside our opening hours then please use our contact form.

One important piece of information is the non-custodial parent's social security number. Other items would include place of employment, home and work address, date of birth and any prior court order information. If you are not receiving CALWorks, your most recent employment information would also be required.

Holmes supplies lighter weight single car doors (10' and under) with extension springs. Heavier double car doors (wider than 10') are supplied with our patented EZ-SET® Torsion Spring System, which is easily wound using a standard 3/8" power drill. Your Holmes retailer can special order the EZ-SET Torsion Spring System for a single car door as well.

For single doors, as a general rule, add 2" in width and 2-1/2" in height to the nominal door size for single doors. For instance, a standard 3/0 x 6/8 door would require a 38" x 82-1/2" rough opening. Pairs would require twice the nominal door width plus 2" as well as an additional 1/2" if there is an astragal ( between them. For example, a standard pair of 3/0 x 6/8 doors with an astragal would require a 74-1/2" x 82-1/2" rough opening.

For all prehung units we REQUIRE that you provide us with your rough opening size. We will build the unit to fit the rough opening size that is provided. If this is for new construction, we normally add 2" to the height of the door and a total of 2" to the width of the door for a rough opening. This allows for the thickness of the jamb and leaves an extra 1/2? in width and height to square the unit.

Klaus Parking Lifts are designed for allowing easy access to the cars parked on the platforms, passengers and luggage should be loaded or unloaded when the car is off the machine. The car should be parked as far to the right side of the platform as possible to allow the most space for the driver to access the car. The lift platforms are available in several widths and it is best to use the widest possible.

Since it is critical to minimize radiation and to provide complete lung coverage in a breathhold, this test should only be performed on a helical (spiral) CT scanner with current software and hardware upgrades.

With laser/light there is almost no adverse reaction. Some pinkness or redness may occur. With electrolysis, there is a slight swelling or redness along the treated area that should subside within a few minutes to an hour. Occasionally slight scabbing may appear two to four days after treatment. These temporary scabs should be left alone as they will disappear in a few days.