Go to the DOS prompt and set the baud rate: mode com[n] 9600,n,8,1 for PP3000S series, and mode com[n] 19200,n,8,1 for PP4000S series, where [n] =1, 2, 3, or 4. To test a PP4000S, on COM2, type: mode com2 19200,n,8,1 Then do a directory listing and output it: dir>com[n] Again [n] = 1, 2, 3, or 4. For COM2, type: dir>com2 The printer should print the directory listing in 40-column mode. To check the lines, do a regular directory listing: dir See similar questions...

A Series 50 parallel printer has a 36 pin Centronics connection that secures the data cable with 2 clips and the serial version has a 25-pin D-shell connection that secures the data cable with 2 screws. See similar questions...

Answer: Yes! We have a serial cable that will work on most serial dot matrix and laser printers. It is a DB9 to DB25 null modem cable. If the communications port on your computer has a DB25 connector, you will also need the 9 to 25 adapter for this cable. We can also provide a DB25 to RJ45 serial adapter if necessary. To find these items, place the word "cable" in the search window (located at the top left side of each web page). See similar questions...

A000030: If you use the serial port for printing or plotting you need to put the DOS MODE command into your AUTOEXEC.BAT file to set up the serial port before you run DANCAD3D.COM (tm) (if DOS MODE is in your AUTOEXEC.BAT file your serial port will be automatically set up each time you turn your computer on.) Some plotters require a "NUL MODEM" type serial port cable to operate. See similar questions...

View printer from the rear (where tickets are inserted).Note: The Serial Data Selections (DIP-Switches) are located on the Serial Interface Assembly. With ticket stock in the printer, apply power while holding the printer's F0 switch, located on the Switch and Display Panel. This will cause the printer to print out its Status Report. Examine this report to insure that all the Serial Selections made were as expected. See similar questions...

Updated Q9: The Network Monitor (/MONITOR option) does not work, but the client can connect to the server See similar questions...

There are many factors that can cause a printer to print slowly from an Operating System, Application. However, there is a small setting in the Lipi Windows 95/98 drivers that may improve the printer's performance. The Lipi Drivers have a default printing matrix set to 360 x 360 dpi (dot per inch) resolution. This resolution value can be reduced easily to 180 x 180 without creating print quality reductions. This 180 x180 resolution will increase the printing speed of each character. See similar questions...

Usually, this condition is accompanied by a blinking error light on the printer's control panel. When the printer cover is opened and closed, the printer runs a self-diagnostics that allows the operator to perform one print operation. Afterwards, the error condition resumes. The most common cause for this condition is when the toner is running low. See similar questions...

In version 1, your serial number is printed on a white label on the front of the sleeve of the CD-ROM. It may also be printed on a label on the outside of the white shipping box. The format of the serial number is XXXX-YYYY-YYY-YYY where XXXX are letters. In release 1.0.1, it does not matter whether you type a zero or the letter 'o' for '0' nor whether you type a one or the letter 'i' for "1". In release 1.0, be sure to type one, not 'i', and zero, not 'o'. See similar questions...

A - You can add a Serial Board or a Multi-Port Board (with serial ports) to add more serial ports to your PC which cost as very little . Or you could use a (Serial) Switch box to connect two devices to one serial port. See similar questions...

You need not own one since printers are located near classrooms, in residence halls, in the library, and in computer labs. You may wish to buy a printer for your convenience; however, Rose-Hulman will not be responsible for it in any way. See similar questions...

Print jobs will print from the nearest networked printer (in the Reference Areas, CALL Lab, etc.) You will need to assign a User ID and password to each print command, then release the job(s) at the print station. The cost for printing is $.10 per page . In order to print from the CALL Lab, a print card must be purchased for $1.00 from Circulation staff, and funds of $.10/page must be added as needed. See similar questions...

Due to the high volume of printers, it is possible that your printer could have been missed. First check to see if your printer has been defined in AASIS. It's possible that the print test was picked up by someone else or mixed in with some other print. If the printer is not defined in AASIS, check with your Agency technical group. The AASIS team may be working with your technical group on some problems with setting up the printer. See similar questions...

No special printer is needed. You can print a test paper using any printer in black-and-white or in colour. See similar questions...

Answer: Yes! We have the serial interfaces for several Okidata dot matrix and laser printers. To find it, scroll to the bottom of the dot matrix page under the title of "Accessories and Options for Dot Matrix Printers". Serial interfaces are available for the ML184, ML320, ML320T, ML321, ML321T, ML390T, ML391T, ML420, ML421, ML490, ML491, ML520, ML521, ML590, and ML591. The PM 3410 and PM 4410 come standard with both serial and parallel interfaces. See similar questions...

The indicator organism that Guam EPA uses in its analyses of recreational beach waters is Enterococcus. The Enterococcus group is a subgroup of fecal streptococci, which are commonly found in the gastrointestinal tract of all warm-blooded animals. This group is more human specific than fecal coliform, thus more indicative of wastewater contamination that can cause acute health problems if there is human contact. See similar questions...