If you get an out-of-memory error (or would like to increase the amount of memory that the server can use), add the "-mx128m" argument when running java/jre. In fact, we recommend increasing the amount of memory available to Java to allow Java and the server to use up to 128 megabytes of virtual memory, if necessary. Alternatively, the config.dct file can be edited to cut down on the amount of memory used by changing the number of threads allocated for each listener.

You probably have run out of virtual memory on your system, or your kernel has a low limit for certain resources. Try this before starting postmaster: ulimit -d 262144 limit datasize 256m Depending on your shell, only one of these may succeed, but it will set your process data segment limit much higher and perhaps allow the query to complete. This command applies to the current process, and all subprocesses created after the command is run.

Wusage contains no arbitrary limitations on the maximum size of a log file to be processed. However, If your log is especially large, and especially when the Summary Reports (summary), Quarterly Reports and Annual Reports options are active, you may receive the following message: This occurs when your computer does not have, or will not allocate, enough memory for Wusage to successfully analyze your log.

One of the most common memory problem faced in older PC system during boot-up is "incorrect memory sizing" or the error number 164. Sometimes failures could be caused by incorrect software setting, sometimes it could be caused by hardware ? which could be easily fixed if you know where the faults lies.

You don't have DivX 3.11alpha but some VKI patch or a newer (never use them!) version. Reinstall Divx 3.11alpha and answer yes when asked to overwrite some files. Then reboot and try again. SBC isn't a wonder solution for good rips. It's a tool for advanced rippers which allows you to push the codec to its limits when using the right parameters. My profiles are but a starting point.. you'll end up encoding the same movie many times to get the ideal rip.

Try increasing the -Xmx value to give the JVM more memory. Performance will rapidly disintegrate if you allocate more memory than physical memory on your machine. At this point, the solution is to buy more RAM or go and have a long coffee break. I've got 512 MB and this is OK for good performance with all but the largest dumps from servers that I've seen. Saving the state once parsed is the best thing to do. Also see the section on memory usage in the documentation.

My program ran fine on the orignal PIC, but it behaves erratically or doesn't run when I put it on a different PIC.

If you can access your security features, verify that you have them set the way you want them. If you cannot access the security features, go into Unibase\misc and delete etpasswd file. You will then have to recreate your security features.

Important Note: Your humble authors got tired of writing dry formal technical prose in the rest of this document, and succumbed to the temptation to try to be funny in parts of this appendix. Sarcasm abounds here. Please do not take any of this personally! The humor-impaired should interpret my comments not as attacks on them, but as an attempt to make fun of myself for being impatient with you, my devoted and valued, if sometimes demanding, users.

Consult your user/owner's manual for details about the original memory configuration and capacity. If you've misplaced the manual, you may be able to contact the retailer where you bought the PC from. If you have a hand-me-down PC or inherited a pre-owned PC, you probably may not have the user manual or know any detail of the original memory configuration or the memory configuration may have been changed.

Close any applications that you currently have running. If you are not sure which programs are running, check the status bar. To close an application, place the pointer on the status bar and right-click the mouse. Select CLOSE from the pop-up menu.

All detected errors are reported through a single error handler function. All memory allocation is performed with three functions which most of our clients override so that they can detect any memory allocation failures and recover. As component software, our products must exist dutifully in the host application - nowhere do we "exit", "assert", "printf", etc.

Check the README file for your specific architecture type. On some systems the default system limits must be changed to allow OpenDX to use more shared memory or a larger data segment. If all else fails, use the -memory flag on OpenDX to limit the amount of memory OpenDX uses.

You will sometimes see an error message something like this: Fatal error: Allowed memory size of 67108864 bytes exhausted (tried to allocate xx bytes) in /var/www/moodle/yyyy.php This error means that the php memory_limit value is not enough for the php script. The memory_limit value is the "allowed memory size" - 64M in the example above (67108864 bytes / 1024 = 65536 KB. 65536 KB / 1024 = 64 MB). You will need to increase the php memory_limit value until this message is not shown anymore.

You are exhausting the available memory that PHP has access to. In php.ini there is a config variable named memory_limit that by default is set to 8MB. Edit php.ini and increase it to a larger value (restart Apache afterwards). If you don't have access to php.ini, you can add this line to your .htaccess file in your gallery2 folder. Usually, unless you are the owner of the server, you don't have access to change php.ini. If there is no .

You are probably running a DOS real-mode only version of TLIB. Try running one of the protected mode TLIBs, such as TLIB32C.EXE (under Win9x/ME/NT/2K/XP), TLIBX.EXE (under DOS), or TLIB2.EXE (under OS/2), or either the 32-bit or 16-bit GUI Windows TLIB. Note: TLIB.EXE is just a copy of TLIB32C.EXE, TLIBDOS.EXE, TLIB2.EXE, or TLIBX.EXE. Which one depends on the choices you made when installing TLIB. So you might need to copy TLIB32C.EXE to TLIB.EXE in the TLIB installation directory so that TLIB.