For units that have been purchased after 2000, when you open the cap (not the battery end) there will be 4 switches on the opposite side of the circuit board from where the cap snaps in. The 2nd switch from the right (or the 3rd switch from the left) is the unit of measure switch. For Meters, push the switch back (away from you), and for Feet, pull the switch forward (towards you).

To change units while using Passport Charts, select TOOLS | OPTIONS | UNITS. Note: Depth unit changes do not affect Raster charts. See similar questions...

Your meters usually are read about the same time each month. You can contact PNM Customer Care to obtain a meter reading schedule. See similar questions...

Yes. Reading a meter is easy to do once you learn how to do so. It also can help you better understand how you're being charged for your energy use. See similar questions...

The bezel of the re-issue SUB 300T has graduations in Meters. There are 2 major diving institutes in the world; SSI and PADI, their courses adhere to the metric system. This was the reason for DOXA to choose the metric bezels but after they received lots of inquiries regarding a SUB 300T bezel with Feet graduations, they decided that the new SUBXXX bezels will be available in Feet, as they were on the original watch. See similar questions...

Each city, county, and property is different. There are many ways in which meters can be read. The following are some examples: Manual Meter Reading System: a meter reader will walk up to your meter or remote counter and read it. Automated Meter Reading System: generally the meter is inside a dwelling or enclosed area that is not accessible. The meter is wired to Meter Counter Modules (MCM) located in the maintenance room of your building. See similar questions...

Meter to feet Length ratio=3.3 (One meter equals 3.3 feet) Sq.meter to sq.feet area ratio= 10.76 (One square meter equals 10.76 square feet) In order to get the feet equivalent, you just have to multiply the meter amount with the length ratio (3.3) to get the amount of feet, or divide the feet amount by the length ratio to get the meter amount. For areas and spaces, just multiply the square meter amount with the area ratio (10. See similar questions...

Very easy. 100 square meters is 1076 square feet. Surfaces are given in square meters, written m2 or m2. See similar questions...

Yes, all meters are read every month. When our meter readers used to read with books and pencils, they were able to do "bar stool" readings (not all did!). That was sitting in a restaurant somewhere and making up readings for customers based on their past usage. With their new hand held computer units it is impossible for them to guess at what the meter reading is. See similar questions...

The Indiana-American Water Company reads the meters and bills the customer each month. This is a private company, and for information and questions you may call them at 1-800-492-8373. See similar questions...

For the remainder of the year bills are calculated based on estimates. These estimates are arrived at by taking an average of the consumption of previous bills. Customers are encouraged to phone in their meter reading to 786-1739. On the water bill there is a section at the bottom called "important notes", this will give the date as to when the readings should be phoned in. See similar questions...

Unfortunately color meters available to cinematographers are far from being scientifically accurate when reading fluorescents. They act as a great comparative tool to determine differences between two given light sources but are inadequate in providing definitive data. You will rarely find two color meters, even if they are the same make and model, that provide equal data. Results between meters may be similar but not identical. See similar questions...

All AstroRide and AstroSlide is priced per square meter. To help you in your estimates a meter is approximately 3.25 feet. A square meter is approximately 10 square feet. See similar questions...

By best approximation, to get sq. meters, divide sq. ft by 10.75, or multiply sq. meters by 10.75 to get sq. ft. The conversion rate is currently 44 INR to one dollar. This is a fluctuating rate. Divide INR by 44 to get close approximation of prices in U.S. dollars. To get the current rate go to: http://wam.org. See similar questions...

The results of the dome calculator are the same unit of measure you used for the radius. If you enter the radius in feet, the strut lengths will be in feet. The dome calculator simply multiplies your number by constants, so the unit doesn't matter. See similar questions...

Hire a cleaning service. A spotlessly clean home is essential; dirt will turn off a prospect faster than anything. Serve cookies, coffee, and soft drinks. It creates a welcoming touch. But be sure the kitchen has been cleaned up; use disposable cups so the sink doesn't fill up. Lock up your valuables, jewelry, and money. Although the real estate salesperson will be on site during the open house, it's impossible to watch everyone all the time. See similar questions...

Yes. Women's feet can grow by as much as one size due to the pressure of supporting extra weight during pregnancy. In addition, pregnant women usually experience more swelling than normal in their feet and ankles, which can aggravate existing foot conditions. Shopping for shoes is best done in the afternoon. Feet tend to swell during the day, and it's best to buy shoes that fit then. Also, be sure to have your feet measured every time you purchase shoes, and do it while you're standing. See similar questions...

It is not uncommon for feet to become larger and wider with age after years of bearing the body's weight. In addition, the natural fat pads that cushion the bottom of feet tend to wear with age, leaving older people vulnerable to many common foot conditions. See similar questions...

Women's feet generally begin to change in their 30s, while men begin to notice changes in their feet in their 40s. See similar questions...