Peeling and flaking of a new tattoo is perfectly normal. Before it actually begins to peel, the tattoo will look like it's covered with a whitish, cracking film. Then you'll see white or translucent flakes of old, dead skin start to peel off and some of the flakes may even contain some ink. Sometimes you can actually see a duplicate image of part of your tattoo peeling off - it's rather disconcerting, but it is also perfectly normal and there is no need to panic.

Note: Boards close to the ground and boards installed on chimneys are the first to become damaged. Look there first. See similar questions...

Yes, DuraTeck can be bent greater than 90 degrees without peeling or flaking. The PVD coated sheets can also be drawn or embossed (within limits based on the application) without peeling or flaking. See similar questions...

Flaking is most often associated with wax contamination and/or poor cleaning prior to recoating. Peeling is usually caused by incompatible products (some pre-finished engineered floors, for example), improperly dried seal or paint or improper cleaning/abrasion before recoating. See similar questions...

Preparation should be completed before applying the product. The flaking and peeling of the structure should be removed by either power washing or light sanding and any damaged or rotting surface should be replaced before applying our product. See similar questions...

Peeling is the final result when a paint film loses its adhesion to the substrate. Peeling may occur between coats of paint (intercoat failure), or all the paint coats may peel from the underlying substrate (total film failure). See similar questions...

Slick, glossy or non-porous surfaces - Prepare the surface to give it more 'tooth' (a rougher surface profile), so the paint will adhere better. This can be done by sanding, using a surface conditioner like Paso, or using a primer designed for slick surfaces. Dirty, greasy or grimy surfaces - Clean the surface with a suitable cleaner (like a TSP solution). Be sure to thoroughly rinse afterwards, and let the surface dry before painting. See similar questions...

Yes. Electrology has never been a problem for tattoos. In fact it is one of the few hair removal methods that doesn't affect the design. See similar questions...

Generally, tattoos heal in about 2-3 weeks after the procedure, during this time, the tattoo should be kept clean, dry, and out of direct sunlight. Many artists recommend the light use of moisturizing lotion on the tattooed area during the healing process. Individual artists may also recommend the use of a topical antibiotic ointment during the first few days of healing. See similar questions...

The recommended procedure for restoring a wrought iron fence with this problem is to either sand blast or wire brush the fence to remove the rust. Once the rust is removed, you should apply a zinc enriched primer, cover it with one or two coats of finish preferably with a rust inhibitor. Just like your car, you can enhance the life span of an iron fence by simply cleaning and polishing the fence with a good automotive wax. BACK TO TOP See similar questions...

There is only one reason why a penetrating stain would peel - something has occurred to prevent it from penetrating properly at the time of application, causing it to dry on the surface. Things that can cause the stain to not penetrate properly are many, but here are a few of the most common causes: Poor ventilation under deck (too low to ground, too close to water, etc.) If the deck is too close to the ground, the wood will absorb moisture from the ground from the underside. See similar questions...

Unfortunately aside from stripping, priming and repainting there is very little that can be done once paint starts peeling. Once paint begins to peel it will continue, even if you get a good paint job over top, the old surface underneath will continue to peel causing the new paint to peel off as well. See similar questions...

This is all a matter of personal taste. You can get whatever you want, and whatever your artist is willing to do. You can choose a picture off the wall, or you can have them create a custom piece just for you. Your only limit is your own imagination. As far as where you should get it goes, just keep in mind what you do for work and the type of social circles you are in. You might want to consider placing your tattoo where it can be easily covered up with normal clothing. See similar questions...