Liners are at least twice as expensive as refinishing and can take up to 3 to 4 weeks from ordering to installation. Click here to read the Miracle Method vs Bathtub Liners.

Unlike our bathtub refinishing process, which is done on-site and in one day, bathtub liners are manufactured off-site as one-piece, heat-molded units that are inserted over your original bathtub or shower surface and then "glued" in place with adhesive caulk. Bathtub liners leave spaces between the liner and the original surface where moisture can condense and stagnate. Cracks in the liner can occur, releasing moisture and lead to unsanitary conditions.

Refinishing costs vary across the country but refinishing will almost always be a fraction of the total cost of replacing a bathtub or ceramic tile surround. Replacing a bathtub and surround can easily cost $2000 or more when you consider the cost of removal, plumbing, setting new tile, etc. Refinishing can often save you up to 75% compared to the cost of replacement! Call 888-271-7690 for an estimate from your local Miracle Method professional.

First of all, to replace something you MUST first tear our the old items. When considering the cost of replacement you must consider tear out, cost of replacement item, labor for installation, not to mention the mess and time it will take. For example, normal costs for relacing a bathtub range from $1,500 - $3,000 and will usually take one and a half to two weeks to complete. Refinishing takes less than one day and will save at least 70% vs. replacement.

The top coatings we use contain solvents, which are necessary to make the finish hard and durable. We use ventilation fans to exhaust air from the work area outside, minimizing the fresh paint like odor. 80% to 90% of the smell will be exhausted within the first 4 to 5 hours and substantially gone within a day.

Refinishing your bathtub with Beautiful Finishes will save you hundreds or even thousands of dollars over bathtub replacement. While a brand new bathtub may only cost $300, there can often be several hidden costs to replacement such as removal and disposal costs, plumbing alterations, and tile work. These costs add up, and you can easily end up spending nearly $2,500 to replace your bathtub. The cost of refinishing varies depending on the size of your tub.

A standard sized bathtub, in reasonable condition, takes only 4 to 6 hours to refinish. The tub will typically be ready to use within 24 hours or even sooner with special curing procedures.

Liner release is smoother and easier, as all 3M Acrylic Plus Tapes utilize a uniquely designed, silicone-coated liner.

Yes, we have a refinishing and restoration service. This service is for Gerstner Chests only. We can not restore products that were not manufactured by us, due to different construction and materials used in making the products. Refinishing and restoration services can meet or exceed the cost of a new chest. When we refinish or restore a chest, we process them one at a time. We have to completely strip a chest of all finish, hardware and felt before we can begin to repair and refinish the chest.

Our countertop refinishing works extremely well on all types of formica countertops, tile vanities, and even cultured marble counters. The finish is very durable and easy to clean. A variety of colors and textures are available including our revolutionary stone finishes which give the appearance of granite countertops, but at significantly lower costs. Click here to read more about countertop refinishing.

The bathtub matters because its lack of damage is evidence. Remember, 500,000 tons of debris fell roughly in the footprint of the towers according to the OGCT. Since debris did not pile up outside the footprint of the towers, either the debris hammered down on the bathtub or it disappeared in a cloud of dust (observed).

Normally three to five hours. All work is done in the fixtures area, and there is no mess for you to clean up. Most of the time is spent conditioning the old bathtub.

Most forms of treatment including acupuncture, massage, ultrasound, medication, TENS, etc. have been used to treat pain and stimulate the healing processes. For the most part the effects of these treatments have been discouraging or provide only temporary relief as they do little more then mask the symptoms. Alleviating symptoms has generally and unfortunately become the accepted norm of treating most conditions.

The NPL and MozPL both attempt to strike a middle ground between promoting free source development by commercial enterprises and protecting free source developers. Like the GPL, they require that any and all changes to code covered by the license must be made publicly available. However, they also allow you to combine covered code with other code to create a larger work without requiring that other code to be covered by the license. This is similar to, but even less restrictive, than the LGPL.

Unlike some other hair loss treatment products available on the market today, Retane is clinically proven to stop male and female hair loss. It is fast acting - most men and women will experience a significant reduction in hair loss within 4 weeks. Retane is an all natural hair tonic that stops hair loss. It does not contain chemical drugs.

The LifePak Challenge has been created to help our Distributors and customers compare LifePak to competitors. Click here to view the LifePak Challenge.

It is quite difficult to answer this question in an objective manner. The first challenge is bringing the film image to the PC so that the both digital and film images can be compared side by side. this introduces several variables: The choice of scanning hardware, and the parameters of the scanning software. The next challenge is that digital and film images fall apart in different ways at the limits.

SpinRite and ScanDisk are entirely different types of products. ScanDisk replaces the original DOS CHKDSK command, which verified the logical file system structure of the hard drive (the newer CHKDSK command no longer performs that function). Microsoft created ScanDisk because people were switching off their computers without first exiting Windows. This resulted in corruption of the file system.

Like VDM-SL, Z [Hayes93] [Spivey92] (pronounced "zed") is a specification language that allows both the specification of mathematical values and program modules. Like LSL, Z allows the definition of mathematical operators equationally (see [Spivey92], section 3.2.2). A Z schema is roughly comparable to an LSL trait. The main difference between Z and LSL is that in Z specifications can include state variables.