You can use a dimmer with a halogen lamps but some low voltage halogen lamps require a special dimmer. Particles from the filament in a halogen bulb will cycle from the filament to the inside of the quartz envelope and back while in operation. Halogen bulbs used on a dimmer will last longer if they are set to full "ON" for two minutes before being turned off — this helps the particles from the filament complete their cycle.

The limits of the halogen technology was reached with the introduction of the PREMIUM lamp. This lamp offer 30% more light on the road ahead compared to a standard lamp. The only way for further improvements was via a new technology. The gas discharge lamp proved the answer.

As a result of grain boundary etching and the development of porosity due to tungsten evaporation (near the end of life, a cross-section of the filament resembles Swiss cheese) within the filament, the resistance increases during life so the current decreases at constant volts. However, the current decrease is not substantial. Light output over life will depend upon both operating wattage and any bulb blackening caused by tungsten deposits on the bulb wall.

There are two kinds of bulbs used in halogen lamps: transparent and translucent quartz bulbs. Materials inside the halogen lamp include tungsten filament, molybdenum foil, and filling gases consisting of a combination of Nitrogen (N2), Argon (AR), Krypton (Kr) and a small amount of halogen gas made up of iodine (I), bromine (Br), chlorine (Cl), and fluorine (F). The base of the lamp is usually made of steatite or heat-resistant metal.

The halogen cycle effectively prevents blackening f the bulb wall so that there is no reduction of light output or color temperature.

The coating used on infrared halogen PAR lamps is made from tantala and silica. It is applied only to the outside of the bulb.

No. Standard 12V automotive power sources are incompatible with the HID light source. The standard halogen bulbs run at 12V, while HID lamps run at approximately 25000V and require several amps to start up. The additional hardware that comes with the kit is needed to convert your car's 12V power source to drive the HID system. The connector is also totally different from any automotive halogen bulb connector. Yes and no.

If you are doing a conversion for a 9006 setup using the custom fabricated beam pattern correct kit, then no modifications to the HID lamp is needed to make it fit. Some headlamp housings where the 9006 bulb is held in by a clip may require the removal of a small tab on the inner edge of where the bulb enters the housing. This can be done using a file, but care must be taken not to allow any particles or dust to enter the headlamp housing.

MR16 lamps without front glass should only be used in a closed fixture (fixture that keeps all parts of bulb enclosed) since the filament tube of all MR16 lamps is pressurized. In the unlikely event that the filament tube breaks, the closed fixture keeps glass particles from leaving the fixture. MR16 lamps with a built-on cover glass can be operated in an open fixture since the cover glass will contain any broken pieces of the filament tube.

There is no danger in doing this, but you will get light only in the middle one of the three "on" positions.

Yes. We carry all replacement lamps for our beds. When you are ready to replace your tanning lamps, call our customer service department. Lamps are upgraded by the manufacturer every year, so it is important for you to call us to get the most compatible tanning lamp for you tanning equipment. We offer the lowest prices on all Wolff tanning lamps and will be able to offer advice when wanting to upgrade your lamps to a stronger tanning lamp.

We recommend C-9 lamps with mounting clips. C-9 lamps are available in 10 watt and 7 watt sizes. We stock pre-made bulk light line and lamps in a variety of colors for this purpose.

The Axis ballast is available for 32 watt T8 lamps, in 4' length or 2' "U-bend" style. We offer 2-lamp, 3-lamp, and 4-lamp 120 & 277V ballasts. We highly recommend using the 32 watt "Super T8" (high lumen) fluorescent lamps.

We use the very fine stained glass in the shades of the Tiffany lamps, and zinc alloy in the bases of the Tiffany lamps.

Halogen is a type of incandescent lamp. It has a tungsten filament just like a regular incandescent that you may use in your home, however the bulb is filled with halogen gas. When an incandescent lamp (one which produces light by heating a tungsten filament) operates, tungsten from the filament is evaporated into the gas of the bulb and deposited on the glass wall.

For this application, incandescent light sources are preferred over halogen. Halogen bulbs produce more heat and glare than incandescent bulbs. (back to top)

Each lamp is carefully carved out of the crystal salt found in the foothills of the Himalayan Mountains. After that, each lamp is securely attached to its base with screws.

The calculation for any question like this is to divide 150VA by 50W, the whole number that you get is the most lamps you can fit on that transformer. In this case the answer is 3.