Yes. Some heaters have built in thermostats, but they can either be removed or inactivated. Remote thermostats can be located so that they are more convenient to adjust than the built in one. Located across the room from the heater, they will also insure that the heater runs long enough to heat the whole room. This is especially true in an odd shaped room where air does not flow readily from one section to another. See similar questions...

Yes, to bypass the in-built thermostat, turn the thermostat on the heater to the highest setting, then use the wall thermostat to regulate the room temperature. See similar questions...

All Broan-NuTone heaters are provided with over heat protectors, which will shut the heater down if the internal temperature rises above preset limits. See similar questions...

Broan-NuTone heaters are designed to provide supplemental heat for rooms you want warmer than the rest of the home or for rooms not adequately served by home's main heating system. They are not recommended for whole house heating. See similar questions...

A baseboard heater requires 30 to 60 minutes to heat the room, provided the heater has been properly sized (adequate wattage) for the room. Baseboard heaters are longer, but not as tall as a fan heater. For example, a 1500 watt baseboard will require 6 feet along an outside wall and is about 7 inches tall. A Register Plus heater grill is 14 inches wide and 7 inches high. Baseboard heaters operate at lower temperatures, making the surface temperatures of baseboards cooler. See similar questions...

The answer is an emphatic and unequivocal Yes. A wall mounted TWIDS System will effectively prevent overclimbing of the wall, by sounding an alarm whenever such an attempt is made. Furthermore, the TWIDS are eminently suitable for installation on top of buildings, to prevent an unauthorized entry through the roof. See similar questions...

A standard incandescent dimmer can be used to dim either line voltage (110V AC) or low voltage (12V AC) lights with an electronic transformer. The DC transformers are only dimmable with low voltage electronic dimmer controls, whereas, the AC transformers are truly dimmable with incandescent dimmer controls. See similar questions...

The Apollo water heater needs to be wall mounted, as high as possible to give good water pressure. Fitting must be vertical. See similar questions...

Thermostats should always be mounted on an inside wall and away from drafts, direct sunlight, or any appliances that could affect the performance (temperature reading) of the thermostat. Be sure the area around the thermostat is clear of shelves, pictures or other wall décor that may impede the airflow around the thermostat. In-wall fan heater thermostats are easiest to mount in the same stud cavity (opposite side of stud) about 5 feet above the heater. See similar questions...

Yes and no. Outdoor models are designed for well ventilated places. Well ventilated does not mean you have a bit of a draft under a crack in the door. In a garage with a window or garage door open, yes you can safely use any of the 12-IR -> 24-IR range of heaters The DESA range of infra-red heaters is the way to go for indoor infra-red heat. These units are designed for indoor use and have safety mechanisms built in to protect you. See similar questions...

Some NuTone bath and utility fans may be wall mounted. See the spec matrix for specific models. Improper installation may affect fan life, safety and your warranty. See similar questions...

Solution: The wall thermostat will maintain the room's temperature according to the temperature you have set on the thermostat. It will turn on the appliance when the room is colder than the thermostat's setting. However, as long as the room's temperature is higher than the thermostat's setting, the fireplace will not start. If you want the fireplace to operate, increase the temperature setting on the thermostat. Solution: There is a blue wire that links the 'TH' and 'TP-TH' ports on your valve. See similar questions...

All Broan heaters are provided with over heat protectors, which will shut the heater down if the internal temperature rises above preset limits. See similar questions...

Yes. All of our ceiling fixtures can be wall mounted. We can even elongate the arm length on the fixture and make a custom bend so the light can shine back at the wall. All we need to know is what radius is required. Additional costs will be added for custom curves and lengths. See similar questions...

This can be done, however the CNK200 requires wall that is thicker than normal 4" wall. (Please verify this information with out Technical Support Department since the total thickness from the bezel's bottom edge to the last hinge for table-mount bracket attachment looks to be less than 4" as per the diagram posted on our website.) The termination switch should be ON if the local monitor is connected through a straight cable. See similar questions...

Most heaters should not be placed directly against walls because the air intake will be blocked. Some heaters are designed with the air intake in the front so they can be placed against the wall. Check the owner’s manual for details regarding the correct placement of the specific model in question. See similar questions...

Cadet recommends you replace the thermostat. A “hot” thermostat indicates that it is not working efficiently; decreasing its accuracy. NOTE: A normal operating thermostat will be slightly warmer than the room temperature by 3 to 5 degrees. See similar questions...

A built-in control is convenient when the walls are already finished. The built-in thermostat is also convenient to install. However, the wall thermostat is a more accurate way to control the room temperature, is more convenient to use, and has a broader selection of models. The use of electronic thermostats provides more accuracy and saves you money on your electric bill. See similar questions...

screws to the ceiling surface. The wiring compartment has a standard size knock-out on top and is 3” in Yes. socket sets are supplied in 6 foot lengths and may be cut to a desired length; follow the detailed instructions supplied with the socket. No, doing that can harm the other transformers. Remove the inoperative fixture immediately. Take one of the operating units and install it in the inoperative location. See similar questions...