A9. Our old boat " Seas the Day " was a single engine 8,000 pound boat that went about 25 knots. It burned about 15 gallons an hour at this cruising speed. Bigger dual engine boats range 20-40 gallons an hour. The Nordhavn 43 is about 55,000 pounds. Yet because of its design and slower speed, it consumes only about 2.5 gallons per hour. Slowing down burns as little as 1.8, speeding up can burn 3+. Said another way, we get about 2.5 to 3.

Yes! The big difference is that wet fuel may take 80% more air than dry fuel. Operationally, you may wish to meter the wet and dry fuel to create a consistent fuel blend or you may want to exhaust the least merchantable fuel before using a more valuable fuel. With the controls designed for this scenario, this can easily be accomplished. In general, any time there are continuous variations in fuel quality, it is desirable to have an operator near by the steam plant.

The Luminarium Outdoor Hearth was designed and built strictly for use with Fire Designs Hearth Fuel. Burning anything other than Hearth Fuel could cause damage to the unit or your property and would void the warranty.

Both will burn less at slower speeds and Moonglow will use more fuel (as all boats do) at higher speeds. Both vessels are powered by diesel engines.

oil - also referred to as Bunker C. To atomize (see next question) properly, the fuel must be kept hot, so steam pipes are routed through the fuel tank in the tender to keep it at 130 degrees F. 1522 did not always burn oil - she was originally built as a coal burner but only stayed that way for a year before being converted. Wood, while burned on real old steam locomotives, does not put out the heat needed to operate larger locomotives like the 1522.

The stove can burn most any fuel: methanol, anhydrous isopropyl alcohol, Coleman white gas, gasoline, kerosine, etc... It has, however, only been tested with methanol and anhydrous isopropyl alcohol. Take appropriate precautions when testing out your stove with new fuels (test outside away from building, etc...). See the disclaimer at the bottom of this page. Methanol can be purchased in at your local hardware store in the paint / solvent section of the store.

No, diesel fuel is not approved for the M601 engines. Use of a un-recommended fuels may cause serious damages to the Fuel Control Unit seals which could result in fuel control problems and loss of power in-flight.

Most patients develop a tan or deepening of their normal skin pigmentation from PUVA therapy. The tanning may be uneven at first, with skin color lighter in areas affected by psoriasis. Some patients also develop freckles - particularly dark freckles - in areas affected by psoriasis.9 Burning from light treatment is a potential serious side effect of PUVA therapy. Regardless of how carefully light treatment is administered, some redness is likely to occur, especially at the beginning of therapy.

It is no longer legal to burn grass clippings because they cause too much smoke. This material must have been grown on the property it is burned on. You cannot move material from one location to another for burning.

The EnviroVent was designed for conventional pottery techniques. A large load of burn-out pieces may momentarily overload the EnviroVent. We recommend smaller loads of burn-out pieces.

To eliminate soot, dilute the alcohol with water. 1 ounce of water for every 7 ounces of alcohol should do it. The times given for question #1 are with diluted alcohol.

Bioheat® fuel is the industry-accepted term for any blend of pure biodiesel with conventional high or low sulfur home heating oil. The heating oil must meet its specification, ASTM D 396 and the biodiesel must meet its ASTM specification, ASTM D 6751, before blending them together.

Fuel injection is a replacement for the carburetors that were around since the dawn of the automobile. There are many basic types of fuel injection, but we should start by saying what a fuel injector is - it's basically an atomizer, something that sprays a mist of gasoline into the air. This helps the gas to mix better with the air and stay in an even suspension, so that it burns more evenly and creates less pollution and more power. (Think of cooking spray vs.

Maximum head (vertical distance the water travels), 590 feet; minimum, 420 feet; average, 510 to 530 feet.

The turbines are predominantly manufactured and assembled in the UK. The blades and connection arms are made of carbon fibre and epoxy resin, optimised for strength and weight.

The turbines will each be 340 feet tall, from the base to blade tip at its highest point. This is roughly the size of a 34-story skyscraper.