kW is more or less equal to 10-20 m² depending on the insulation of the house. It is recommendable to choose a smaller stove as the combustion will get cleaner if you fire hard in a small stove instead of slumber use in a large stove. See similar questions...

You can have as much land as you choose. Change the amount of land you have and your monthly fee will adjust accordingly. See Virtual Land: Cost. See similar questions...

Very easy. 100 square meters is 1076 square feet. Surfaces are given in square meters, written m2 or m2. See similar questions...

Meter to feet Length ratio=3.3 (One meter equals 3.3 feet) Sq.meter to sq.feet area ratio= 10.76 (One square meter equals 10.76 square feet) In order to get the feet equivalent, you just have to multiply the meter amount with the length ratio (3.3) to get the amount of feet, or divide the feet amount by the length ratio to get the meter amount. For areas and spaces, just multiply the square meter amount with the area ratio (10. See similar questions...

Exhibition Room 1 measures about 264 square meters, Exhibition Room 2 measures about 165 square meters. See similar questions...

All AstroRide and AstroSlide is priced per square meter. To help you in your estimates a meter is approximately 3.25 feet. A square meter is approximately 10 square feet. See similar questions...

That is very difficult to answer without seeing you. This is because the amount of grafts required will ultimately be dependant upon the texture and quality of your hair (i.e. darker, coarser hair may require less grafts to cover the same area as compared to lighter colored, fine hair). It will also be dependent upon your density goals. See similar questions...

That is very difficult to answer without seeing you. This is because the number of required will ultimately be dependant upon the texture and quality of your hair, i.e. darker, coarser hair may require fewer to cover the same area as compared to lighter colored, fine hair. It will also be dependent upon your degree of baldness and your density goals. See similar questions...

Generators are classified by the "combustion" system and their rated electrical output. Combustion refers to whether an IC engine, microturbine, gas turbine, or fuel cell is used to convert the fuel to mechanical energy. It is in quotes because while most of these technologies use a combustion process, fuel cells use a chemical process without combustion. The electrical output or capacity is the number of kilowatts (kW) or megawatts (MW) of power generated. See similar questions...

By best approximation, to get sq. meters, divide sq. ft by 10.75, or multiply sq. meters by 10.75 to get sq. ft. The conversion rate is currently 44 INR to one dollar. This is a fluctuating rate. Divide INR by 44 to get close approximation of prices in U.S. dollars. To get the current rate go to: http://wam.org. See similar questions...

Each solar module is approximately 5 feet (1.5 meters) long and 2½ feet (0.75 meters) wide. The modules are always grouped in a set of four, and the minimum number of modules for our smallest system is twelve modules. This requires an area of at least 120 square feet (11 square meters). See similar questions...

A Kilowatt is a measure of power equaling 1,000 watts, describing the rate of energy use. For example, ten 100-watt light bulbs use one kilowatt of electricity. See similar questions...

A QC Device should only be run on its assigned meter, as indicated on the label of its protective box. QC Device Code Chips are programmed with data specific to the individual meter. See similar questions...

If God is leading you to increase the UWB pledge you made earlier in the year, you have the option to include it in the original 3 year period or to start the clock over and begin a new 3 year period. If you choose to start the clock again, please indicate that on your pledge card by writing in 2007 to 2010. See similar questions...

Yes, in many cases. One thing to bear in mind is that the inside dimensions of our 1 litre square jars are 80x80 mm, and the paddles on some jar testers have 3" (76 mm) wide paddles. Therefore, with these testers there will be only 2 mm clearance between the ends of these paddles and the jar walls, so careful centering is necessary. You may prefer to use 2 litre jars with this type of equipment. See similar questions...

The MO (molecular orbital) is normalized, and the AO (atomic orbitals) are normalized. But the AOs are not orthogonal. This is why the simple algebraic norm of the coefficients is not 1.0. In order to do any quantitative work with the coefficients of the MO you will need to know the values the AO overlap integral. This is usually referred to as the overlap matrix and is represented as 'S'. See similar questions...

A standard square is 15 inches on all sides. A square can be made from the back, front, or both sides of a t shirt, sweatshirt, jersey, etc. It can also contain anything you want us to sew onto a 15 inch blank square, such as sweatpants, jackets, boxer shorts, towels, etc. Back to top See similar questions...