DIPS stands for “Ductile Iron Pipe Size”, a sizing standard based on the outside diameter of ductile iron pipe. DIPS pipe sizes are primarily used in water systems where ductile iron pipe sizes were commonly used, and is becoming an increasingly popular sizing standard for polyethylene pipe.

The first models are standard 2 inch pipe, with 4 inch models in planning. The 2" unit fits to a 4 bolt ANSI 150 flange. The instrument is rated to ANSI 300 and 4-8 bolt adapters will fit the instrument to ANSI 300 pipe systems. See similar questions...

IPS stands for “Iron Pipe Size”. IPS pipe is sized with nominal outside diameter, and has been the way that most polyethylene pipe has traditionally been sized. See similar questions...

DN stands for “diametre nominelle”. These sizes, in millimeters, are set by the International Standards Organization and are in use throughout the world. They roughly correlate, converting inches to millimeters, with the nominal pipe sizes commonly in use in North America. See similar questions...

CTS stands for “Copper Tube Size”. Polyethylene pipe is available in small diameters to match this standard, which is primarily used in the plumbing industry, as well as occasionally in natural gas applications. See similar questions...

Sensors with a 1" transducer should be installed in 2" stand-pipes. Sensors with a 2" transducer should be installed in 3" stand-pipes. Click to view stand pipe installation tech-tip. See similar questions...

Typically, the piping should be sized large enough so that frictional pressure drop within the piping system make up less than 10% of the operating pressure of the system. For example, a system operating at 100 psi should have less than 10 psi of frictional pressure losses in the piping system. Pressure losses in a piping system can be readily determined using the "equivalent length" method that is found in most piping handbooks. See similar questions...

The pipe should be a minimum of 1 ?" ID when using a size 1 purge unit. The bigger the ID of the pipe the better it is for creating the proper flow. See similar questions...

Regulator body size should never be larger than the pipe size. In many cases, the regulator body is one size smaller than the pipe size. See similar questions...

In the borehole the pipe size should be between 1" and 1.25" depending on depth. One-inch can be used on bore holes up to 300 ft. in depth, and 1.25" on bore holes deeper. Common pipe sizes for polyethylene are ", 1", 1.25" 2", 3" 4", 6", 8", 10", 12" 14", 16". See similar questions...

There are a range of dips that we can provide and you are welcome to provide your own or suggest particular favourite for us to get for you. Certain foods are not suitable as they can adversely effect the quality of the chocolate and or the operation of the fountain. Our dip range includes strawberries, pineapple, banana, seedless grapes, kiwi, mini profiteroles, chocolate brownies, fudge squares, marshmallows, mini donuts etc. See similar questions...

Yes, if you have a special dip that you would like we will do our utmost to provide it. However, we do ask that only foods provided by 'Hot Chocolates' are used. See similar questions...

Biologically, Lauricare dip is equivalent to other dips teat dips that have been documented by the NMC protocols, (B or C). All dips successfully documented by NMC protocol are considered to be effective in preventing new intra-mammary infections. There are three important factors to remember: Protocol B & C data demonstrates the ability of the teat dip to reduce new intra-mammary infections. Lauricare dip is on the NMC published list of effective teat dips. See similar questions...

The Lauricare dip is compatible with iodine based products, however, Lauricare teat dip is not compatible with chlorhexidine based products. DO NOT EMPLOY AT THE SAME TIME OR IN EQUIPMENT PREVIOUSLY USED WITH A CHLOROHEXIDINE CONTAINING PRODUCT. THIS INCLUDES USING A CHLOROHEXIDINE UDDER WASH AND THE LAURICARE DIP AS A PRE OR POST DIP. The Lauricare dip is not compatible with bleach. See similar questions...

Yes. Using the supplied Table Manager program you can modify the pipe tables shipped with the program or create your own custom pipe size tables for specialty pipe material. See similar questions...

Why not extend the pipe slightly, using a compression fitting with a special imperial size olive, enabling you to add a short length of metric piping? Then use a push fit end cap as usual. Alternatively, some engineers will adapt the outer end of their dump hose to fit onto one side of this removed radiator, with another adapted tube leading from the other side of the radiator to the drain. This way, every time you dump, you’re putting a good flow of water through the radiator. See similar questions...

We have other CPVC brand known as Astral FlowGuard. CPVC pipes available from ?" to 2" (Copper Tube Size). You can easily join Astral Aquarius PVC pipe (Iron Pipe Size) with Astral Flow Guard CPVC pipe (CTS) with suitable Transition fittings. Transition of CTS to IPS or IPS to CTS is easily possible with our one step solvent cement. All information contained in this manual is given in good faith and believed to be accurate and reliable. See similar questions...