Loose cables or cables that are not grounded properly can cause static. Check the connections to make sure all cables are connected correctly. Also, try adjusting the input volume from the media player you are using or from the sound control panel in your system tray.

If you are using a Creative Labs AWE 43 or 64 sound card, the audio playback quality will be poor if full-duplex mode is enabled. This is a condition caused by the Creative Labs Driver. The audio is recorded in 16-bit, but will only play back in 8-bit as long as the full-duplex mode is enabled. Once you make a recording, choose Options | Audio | Advanced and uncheck the "Enable Simultaneous Record/Playback" item.

You will notice that you hear static over your BlackBerry speaker when your device is connecting to your network (indicated by arrows in the upper right hand corner of your screen). The static is reduced by a strong network connection, or by listening to the QuickPlayer through earbuds. The browser you use to visit getQuickPlayer.com can sometimes affect our ability to recognize your BlackBerry model. If you encounter this problem, visit getQuickPlayer.

If you're hearing static, first check the battery life on your phone to see if it needs to be charged; there may be enough power to attempt a call, but not enough power to locate the signal. Next check your bars of signal strength and ensure your antenna is fully extended; you could be in a poor reception area or have an interference such as weather conditions, building structures or other electronic devices.

Please adjust the preference of your Real Player for the most reliable video by opening Real Player and going to Tools-->Preferences-->Playback settings. Set buffer play to 45 seconds. Then click on Hardware in the prefernces menu and Video Card Compatiblity at the bottom should be set to most reliable or Use Optimized Video Display Unchecked (depending on your version of the Real Player). Currently, the program is set up to send both greetings. However, if you are not having a party at Chuck E.

If you can't hear sound from your speakers, it means the speakers are not connected properly, the sound card isn't setup correctly, or the speakers could be defective. First, check the speaker-to-computer connections. Make sure the cable connected to the "Audio In" jack on the speakers is also connected to the "Speaker Out" or "Line Out" jack on the sound card. You can test the sound card jack by connecting headphones to it.

If you can't hear sound from your speakers, it means the speakers are not connected properly, the sound card isn't setup correctly, or the speakers could be defective. First, check the speaker-to-computer connections. Make sure the cable connected to the "Audio In" jack on the speakers is also connected to the "Speaker Out" or "Line Out" jack on the sound card. You can test the sound card jack by connecting headphones to it.

To eliminate this open your audio settings window (Playback) and mute the microphone slider by clicking on the square box next to the word "mute". This will put a check mark in the box muting your audio. It does not affect your microphone audio into the Echolink and internet. [ Top ]

Note: Noise could be coming from incoming calls and/or cordless phones which DRN has no control over.

It is not normal to hear buzzing. This can be caused by interference with cordless handsets or faulty grounding in the phone circuitry. Try another corded phone to see if the buzz stops. Connect your phone directly to the IAD to eliminate any possible faulty wiring problems in the home circuitry. This can be a result of a carrier routing particular calls over a route where high latency occurs.

If you have an older machine (Pentium 2 class), close any unnecessary applications to free up resources. Let MixMeister finish calculating the BPM and building plots. (Consider leaving it running overnight.) Then, try playback again.

When you can only hear sound from the front speakers, it usually means the sound card does not support surround sound, and/or the sound card is not configured correctly, the speakers are connected incorrectly or the speakers could be defective. First, make sure your sound card supports surround sound 4.1. A surround sound card should have a front and rear speaker jack.

Hearing is a series of events in which the ear converts sound waves into electrical signals and causes nerve impulses to be sent to the brain where they are interpreted as sound. The ear has three main parts: the outer, middle, and inner ear. Sound waves enter through the outer ear and reach the middle ear, where they cause the ear drum to vibrate. The vibrations are transmitted through three tiny bones in the middle ear called the ossicles.

Well, there is (almost) no demand for static libraries so far. If you want them anyway and are capable to deal with the problems as described in the in question above, then you may retrieve the set of Makefiles for OS/2 and build them on your own.

Cell phones and radios can create interference with electronic devices due to the signal strength and frequencies that they use. We have found that some of these devices create a "clicking" or "static" sound through the telephone speaker. The interference can be minimized by moving the cell phone or radio away from your phone.

Communicator Power will eliminate all those pesky weak / dead battery related problems. For the one time cost, you will always have optimum power for your communicator. Communicator Power hooks up to any machine, and in minutes NO MORE Buying, Changing and/or Charging Batteries, Send us E-mail, with questions and/or comments. We would like to talk to you about riding safely with "Communicator Power".

You must get the latest drivers for your sound card. These should be available from the manufacturer's website. return to top DVD X Point has to have a valid Default Content Folder to work properly. Uninstall DVD X Point, then reinstall. return to top

Answer: You must get the latest drivers for your sound card. These generally are available from the web site for the manufacturer of your drive. Answer: For safety reasons, DVD X Maker requires that the DVD Video Path end in "\DVD-Video\". The files in this directory are deleted and rebuilt when you build and burn a DVD. DVD X Maker will not automatically erase the files in that directory unless the proper naming convention is used.