ADSL is asymmetric - that means that the download speed is different from the upload speed. In South Africa Telkom allows up to a 1024kb/s download speed and a 256kb/s upload speed.

Typical residential offerings usually have a maximum of 1.5Mbps (1.5 megabits per second), but special connections for home and office can be obtained to go well above that. There are two limiting factors that are in place for most connections: the modem and the wiring used to transfer the signal from the modem to the computer. Most home use DSL modems are limited to 10Mbps on the user (LAN) side.

k compatible modems do thousands of line checks to determine the maximum speed that your connection to your local phone company will allow. Due to FCC regulations, standard phone lines are limited to a maximum speed of 53kbps -- but most phone lines are not even able to allow connections at that speed. Most typically, 56k users will see speeds in the high 30's and low 40's, depending entirely on the quality of their phone lines.

A.Download speed is also sometimes referred to as transfer rate. The primary difference is that the connect speed is what you connect at when you first log on to the internet. That speed will increase greatly when you begin to move away from the home page and go from site to site. The transfer rate on the digital service can reach to 44k+ depending on which site you are going to.

Initialization Strings Can Affect Speed. Did you know that connection speed on a 28.8/33.6 modem does not affect transfer rate? This is because all modems over 14.4 utilize auto baud technology that allows them to adjust speeds according to line conditions. Modem performance is mostly controlled by its initialization string (INIT string). By customizing this line in your modem configuration, you can exceed factory settings and sometimes achieve superior bandwidth.

Elirion uses the same network providers as other major internet service providers such as MSN and AOL, so your connect speed is likely to be the same.

Sometimes a better quality modem helps. Switching from a WinModem to an external modem often yields a small improvement in connect speed.

You probably have a 56k modem on a phone line that's not 56k capable. There was a modem test line run by 3com you could use to verify your phone line is compatible with 56k modems.

If your connection is excessively slow or frequently dropped, you may have some line noise problems. See the section above pertaining to line noise. You should always have the latest firmware for you modem - especially if you have a 56K modem. Firmware updates are done to fix common problems with modem connections. Failing to keep your firmware current is a major cause of "it used to work and now it doesn't" problems.

The connect rate reported at logon is just a snapshot of that moment. Your actual rates will fluctuate up and down during the time you are connected. Normal connect rates on analog lines will be between 21.6 and 28.8. It is difficult to achieve 33.6 connect rates on analog lines.

Yes. In order to hook up more than one computer, the computers must be networked. There are several ways to network computers, such as using a hub or a router. See our Home Networking page for more information.

Even though your CD or DVD recorder may be capable of recording discs at extremely high speeds, many computer systems are unable to provide data to the recorder quickly enough to keep up. If your computer system cannot supply data at the rate the recorder requires, an error called a 'buffer underrun' occurs, which typically ruins the disc. To prevent this type of error, we recommend that you record at a slower speed than the maximum. (Back to top)

Around 1 to 5 seconds is average, but it could vary depending on ISP. Some users report up to 30 seconds, this may be a fault at the ISP end, if you consistently get long connection times report it to your ISP or visit the forums to discuss. Win2000 crashes in a Blue Screen of Death? BSOD can have many causes, a fairly common one linked the Alcatel USB modem is when running Norton Internet Security or Norton Personal Firewall, the blue screen shows the message "IRQL_NOT_LESS_OR_EQUAL.

The general rule is that speed is governed by the speed of the slowest component. However modem speed can have a positive effect if it best matches the level of other technology in the system or network. Ie: Though a "connect 115.2" message may make you feel warm and fuzzy it does NOT mean that is the speed it will run at throughout the session and it can actually slow the overall link down if it outstrips the quality of the phone line or systems being connected.

iZoom High-Speed will require that you have a NIC (Network Interface Card also known as an Ethernet card) installed in your computer. Almost all newer computers have them installed. Check with your retailer to be sure. When purchasing a NIC card, 10/100 mpbs is recommended.

Telephone line quality has a lot to do with connect speeds to the Internet. On average, we see connect speeds ranging from 24000 to 52000 and that depends on your location. In the Winnemucca area of Grass Valley, and in the outlying areas of Battle Mountain, the telephone line quality for digital transmission is poor and that is the reason for low connection speeds.

Occupational growth is defined using projections data. These data list the fastest growing jobs (percentage of growth), largest job growth (numerical growth), most annual openings, etc. Eight of the 20 fastest growing jobs are related to health services and five are related to computer technology. Fastest growing occupations, defined as a percentage of new growth, also have a minimum of 100 annual openings. Additionally, more than half of these occupations have higher than average wages.

I only forward these things back to whoever was on my senders list. Most of my friends have specific mailing lists when they want mass random mail, and hate HATE HATE this sort of thing, so I never add email addresses to the loop.

Our Blue Gene is only just enough to launch this project. It is enough to simulate about 50'000 fully complex neurons close to real-time. Much more power will be needed to go beyond this. We can also simulate about 100 million simple neurons with the current power. In short, the computing power and not the neurophysiological data is the limiting factor.