The SBG1000 reset switch is a small hole in the back of the unit. It is located between the cable and USB connectors. Using a small, sharp, pointed object such as a paper clip, press and hold the reset button on the back of the unit for 10 seconds.

Macros are a string of commands that you create to perform complex actions with the touch of a single. You may need to have twenty IR commands sent to power on all of the devices in your system, just by pressing one button. You would create a series of macros to make it muck easier to operate your system. See similar questions...

You can obtain a new R7 manual directly from our website. It is available for download as a PDF (portable document format) file.Back to Top See similar questions...

If you move or delete the pdsj folder from your computer the system will initialise next time you log onto Proquote, i.e. system default settings will be restored. This means that all of your client accounts, stock lists, and user defined fields, etc will be lost. The location of the pdsj folder is determined by your browser, and varies according to operating system. See similar questions...

Please note that System Restore does NOT magically restore your ENTIRE system to a previous state. It ONLY reverts some important parts of your system. Therefore it is highly recommended to FIRST uninstall the problematic software, BEFORE you use System Restore to go back to a point prior to the installation of that software. See similar questions...

Answer The factory default setings are shown in the Programming Manual with a asterisk (*) character against them. Answer In most cases the scanner will not need programming because it will already be pre configured for you. However if you need to change the configuration it is simply a matter of scanning the appropriate barcode(s) from the programming manual. See similar questions...

The default settings can be loaded from a menu selection in the IWMS utility, or the reset button on the back panel of the AP can be pressed. See similar questions...

Reset the AP manually. If user forgot the user password or user WLAN access point has locked up, user can reset it to factory defaults by performing the following steps: Wait for about 5 seconds. Release the push button, then the access point will restart with the factory default settings. The AP reset timing is around 60 seconds. Please apply power line cable again to enable default setting. See similar questions...

Yes. DHTML Menu Builder will not allow you to cerate more than 32,767 groups and 32,767 commands. More than enough we think ;) See similar questions...

First, log into the SiteBuilder wizard located at www.CompleteSiteInteractive.com. In the left navigation bar (gray), choose the Web Page you wish to restore the default text on. Then simply click on the “ Revert to Defaults ” button on the botom, right hand side of the page. This will restore the default text for that particular page only. See similar questions...

Check to see that you do not have a SCSI device connected. If stuck in the Recovery console menu, power down the PC and disconnect the SCSI cable. Repeat the "Restore to Factory" process and the system should boot into the operating system after the factory restore. Power down the PC and reconnect the SCSI cable. Blackberry only supports text pdf's (Adobe PDF's) not image pdf's which is what eCopy and Canon generate. See similar questions...

The error message: "invalid serial number" is displayed when emulations are activated from the ConsoleAdmin See similar questions...

Note: this assumes you have an SD or Compact Flash card, and have some way of connecting it to your PC. If you do not, it is highly recommended that you acquire one as you will not be able to do "emergency" firmware upgrades without it. Download the latest firmware to your PC and rename it to r3.upk. Create a new directory on your aforementioned flash card called "newpackage" (no quotes). Copy the r3.upk file into the newpackage folder. See similar questions...

You can replace the default DbUnit data type factory to get support for custom data type. DbUnit provides extended factories for some vendors, which are located in org.dbunit.ext subpackages. IDatabaseConnection connection = new DatabaseConnection( jdbcConnection, schema); DatabaseConfig config = connection.getConfig(); config.setProperty(DatabaseConfig. See similar questions...

You can reset this router to factory default by clicking the Web interface "Tool box" Reset to default button. Restore by hardware when the router power on. First, hold the RESET button about 5 seconds (M1 will start flashing about 5 times), move away the hand. The RESTORE process is completed. See similar questions...

Press the Menu and then the upward arrow key, you will see the Reset option on the LCD. At this point, enter the full 12 digit of the MAC address or Product ID of your phone (printed at the back of your phone). e.g., for "A/B/C", press the "2" button until you see "A" or "B" or "C" appears, for "D/E/F", press the "3" button until you see the corresponding character. Then continue to enter the complete 12 digit of the MAC address. After that, press "Menu" again. See similar questions...

To reset GL2422-AP to factory default, when it is powered ON, press "reset" button more than 5 seconds. After you release the button, all LED will flash and back to normal, it will be back to factory default settings. See similar questions...