It is advised against drilling your Americast sink, because it will void the warranty. However, it can be done by following these simple steps:

Although most our tanks are non-tempered glass, we do not recommend drilling holes by yourself. Drilling holes by yourself voids the warranty. You should have a qualified technician drill holes for you.

Yes, we drill holes in specific locations in order to reach all the areas that are likely to rust. For example, the doors, the rocker panels and the back fenders.

No, you do not have to do any drastic modifications like that to your motorcycle, although for some models you may have to relocate your turn signals. Even Duece owners do not need to drill holes in their fender.

While drilling holes was once a common practice in the rustproofing of vehicles many years ago - and there are still some applicators that will drill holes - it is completely unnecessary. At Dynamic Shine we insert a polymer mist applicator tool into the manufacturer-provided holes and drain sites of the vehicle.

Unlike steel or concrete poles, the Powertrusion pole is easily drilled in the field when situations arise for hardware or equipment to be added. We suggest a high-speed carbide tip drill bit be used, but if that is not available a standard auger-bit can be used. (See Application Guide.)

Yes, BHK has the ability to drill holes to accomodate the installation of fronts or KD fasteners. Depending on the required pattern, this service can be provided at no extra charge. Please submit a drawing of your drilling requirements for additional information.

Drilling (or sawing) of neodymium magnets is absolutely not recommended. First of all, the material is brittle and fragile. Secondly, drilling causes combustible dust and, thirdly, the heat caused by the drill can possibly demagnetise the material. Specialists can work with the magnets with specialised diamond-tipped tools and constant water cooling. However, this normally occurs prior to magnetisation of the material.

Smallest achievable hole size (and largest achievable hole size) is dependent on the material, material thickness and laser used. It is possible to drill 1 micron holes through thin material at aspect ratios of up to 100 to 1. It must be remembered, however, that there will usually be taper associated with the holes and the entrance diameter will be larger than the exit. We normally specify EXIT diameters.

Zinc provides sacrificial protection to steel with steel beginning to corrode once there is no zinc present. Applying a zinc-rich paint over a drilled or exposed area will provide corrosion protection.

Use a carbide-tipped masonry bit or diamond drill bit; Fegular twist-drill bits can't cut through the fire-hardened glaze. Not necessarily. Porcelain tile is no different in temperature than anything else in the room except that it holds its temperature better because of its mass. Of course, cool is good in warm weather climates and it's easy to warm things up with an area rug or two.

We recommend the hole be a factory supplied option. What we do is actually disassemble the valve, indicate the ball dead center on 1 side, drill deburr, reassemble and then test the valve. This way we are certain that if the valve is installed following the manufacturers instructions, there will be no problems.

We recommend securing the model on a survey table. Then prepare the drill hole in the model using a drill press (available from any hardware store). Freehanded drilling is not recommended.

The wood at the center of the piece has almost a  “Zero” velocity across the tip of the tool, and that can make it difficult to turn. Sometimes this is a problem, and sometimes it isn’t. Sometimes I drill into the center, and sometimes I don’t. Sometimes I don’t, then change my mind, and drill later.  Sometimes I do when I didn’t need to, and then it was a wasted effort.  I don’t think it matters.

No. The system can be installed differently depending on your needs. We recommend drilling a hole to allow the camera to be mounted on an angle, which gives you depth perception and a wider viewing area.

No. Although some offices use this technique to acquire better adaptation, we at ChicSmiles do not recommend drilling a hole. With no hole drilled, you can easily remove this crystal without further procedures to cover the hole.

No, please DO NOT drill your Granite sink. Please follow the installation directions included with your sink packaging for knocking out faucet holes.

NO. ALL HOLES ARE DRILLED THE MORNING OF THE FISHING CONTEST. NO ADDITIONAL HOLE DRILLING IS ALLOWED BY ANY CONTESTANT. YOU MAY WANT TO BRING AN ICE CHISEL AND ICE SCOOP TO CLEAR ANY ICE THAT MAY FORM PRIOR TO THE CONTEST STARTING.