With the current adapters you cant, the USB modem is the DSL equivalent of a WinModem and requires some processor power to perform the modem functions and convert the ATM data into TCP/IP for presentation to the PC. There is a Draytek device however which can effetively act as a router and presents ethernet to the user side. See details here.

Yes, but you would have to implement the equivalent of Echelon's xDriver software. The best choice for using the i.LON 10 Ethernet Adapter without LNS is to use Echelon's OpenLDV driver. It is available free of charge at www.echelon.com/openLDV. Yes, though the algorithm differs from the i.LON 600 LonWorks/IP Server. This question is usually asked when trying to figure out how much bandwidth an i.LON 10 Ethernet Adapter might consume on an Ethernet segment. For example, if the i. See similar questions...

Ethernet connection is up to 100 times faster than a modem connection and allows access to printers and fileservers, unlike a modem. Also, you would have to obtain an outside Internet System Provider (ISP) at a cost. With a modem connection you have to wait for an open modem line; with an Ethernet connection the network is always there for you to use, and it doesn't tie up your phone line. Ethernet Adapter: (or "Ethernet card"): Also called a network interface card (NIC). See similar questions...

Some DSL modems carry USB capability. This is useful alternative in instances where a network card cannot be installed. Please note that you cannot use the USB port of a usb HUB to extend the wire length between your modem and PC, or share the access to multiple systems. You can use the USB and Ethernet ports at the same time to facilitate access on two machines provided the advanced modem routing features are enabled. See similar questions...

Yes. There are several manufacturers of 10/100 BaseT Ethernet to wireless bridges. One example is the LinkSys WET11 Ethernet bridge. See similar questions...

Yes. When you install a driver for your device, a new virtual COM port will be created. You can use the COM Port Scanner utility available on our download page to locate the COM port. See similar questions...

There are two RJ45 ports at the back of the Bluetooth Access Point, LAN and Uplink (port with a X sign). If you are connecting via a router, please use a standard RJ45 ethernet cable and plug into the LAN port. If you are connecting directly from the ethernet jack on the wall, then you should use a standard RJ45 ethernet cable and plug into the Uplink port (or a crossover RJ45 ethernet cable and plug into the LAN port). See similar questions...

Not supported yet but will be in a future Solaris Express release. Use an Edgeport adapter and a serial modem for now. Check this blog on USB communication device at: http://blogs.sun.com/roller/page/psum?entry=solaris_and_usb_communication_device See similar questions...

It is an expansion card placed in a computer to support the ethernet network protocol across digital communications lines. See similar questions...

Probably. Any wireless receiver supporting the industry standard 802.11b or 802.11g protocols should work. However, in rare cases, we have found wireless receivers which had compatibility issues with the computer upon which it was installed. See similar questions...

Yes if you specify this at time of ordering our installers will provide you with a suitable USB to Ethernet converter at time of installation See similar questions...

If you are connecting directly to one PC, under windows 98SE, 2000 or XP, either Parallel or USB is usually fine. However, the way XP handles USB devices may cause you to lose the device occasionally. This is because XP assigns virtual USB ports to multiple devices on the same USB bus. If the plotter is switched off or disconnected when the PC is booted up, it may be found later as a new device on a different virtual port, and the driver may need to be installed again. See similar questions...

Absolutely not. The performance of your DSL modem is closely dependent on using the manufacturer's recommended power source. Using a generic or repaired adapter will adversely affect the DSL signal and could damage the electronics in your modem. If your modem or DSL appliance fails to power up and you believe that the adapter has damaged, please immediately contact our technical team for assistance. See similar questions...

NT4 does not have usb support, and we recommend our users to use either Win 98 or Win 2000. We can offer support for NT4 only for large customers under special conditions for our devices- including usb to serial or parallel. See similar questions...

Not only will it not work, you may damage your device. In order for a device to work with USB it must be compatible and have appropriate drivers. Some early releases of the Freestyle Pro and Precision Pro were not USB compatible; if it did not come with an adapter you are out of luck. See similar questions...

At this time we would recommend the certified Cat 5e or the special Cat 5 ENH offered by the manufacturer we use. We feel these cables offer the security of conforming to a ratified standard, while also leaving the needed room for growth towards Gigabit Ethernet applications. Having Cat 5/5e installed for both your data and phones offers you the flexibility to use your phone jacks as network jacks in the future (assuming you have the cables terminated onto a patch panel). See similar questions...

Yes. The i.LON 10 Ethernet Adapter (version 2.x and higher, available from April 2004) supports an external modem attached to its serial port. When used with an external modem, the i.LON 10 Ethernet Adapter uses PPP as the serial protocol. The i.LON 10 Ethernet Adapter version 1.x does not support PPP. See similar questions...

PC/104 systems with multiple processors or peripherals that have Ethernet interfaces can use a PC/104 Ethernet switch or hub board to be networked together. Fast Ethernet and 10BaseT switches or hubs are available with auto-MDI-MDIX network installation and up to five auto-configurable 10/100 transceiver ports. Ethernet connections are made through either onboard RJ-45 jacks or via right-angle Molex connectors that can be used to mount RJ-45 jacks in a faceplate, endcap or enclosure. See similar questions...

Again no (though see earlier sections for other ways to share files between PCs and Acorn machines). Work is ongoing to add support for AUN to Linux, both over Ethernet and (when running on suitable hardware) native Econet, but there is no usable implementation yet. All Acorn computers since the Master have had their Econet station number stored in the first byte of CMOS RAM. If the battery goes flat, or you reset the CMOS RAM, it will get cleared to zero - this isn't a legal station number. See similar questions...