Yes you can. All you need to do is provide a Radiantec mixing valve to step down the temperature of the water to the radiant circuits. You mix hot water from the boiler with return water from the floor to provide a lower temperature.

A modern radiant heating system is an energy-efficient heating system in which hot water is passed through tubing that is laid either within a floor, installed beneath it, or run within baseboard casings. In the former two methods, the thermal mass of the floor itself stores and radiates the heat.

No, the system generates low temperature heated product that works well with radiant floor heating systems, warm air heating, Solar Domestic Hot Water (SDHW) heating systems and other types of low temperature heat distribution systems.

Both Ground Source and Air source heat pumps can be linked into existing heating and hot water systems and will work well and efficiently. However they work even better well with underfloor heating.

No, the system will combine the comfort of radiant with the responsiveness of hot air. It may be desirable to control the radiant with a floor sensor.

Yes, this is entirely possible. Temperature control is the issue. You can use one of our heat exchanges to change the steam to hot water. Then you can use a mixing valve to control temperature of the hot water. You may want to consider the use of a safety control.

You will not need the humidifier as much because the air is more stable and not being changed as much.

Yes. Many homes with radiant heating also have a central heating system such as a furnace or boiler, it can act as your main heating source, especially if you are building a new home. You can use the same heating source for your: In the floor, underfloor, Slimline baseboard and domestic hot water if the heating source meets the BTU output required.

Any natural resource can be used to fire the heat source, natural gas, propane, electric, wood, etc. It does not matter what the heat source is, as long as it can provide the necessary BTU's (energy) at the required design temperatures. There will be a variance between heat sources based on efficiency, response, cost and capacity.

This is not affected if you switch. Some suppliers may offer you their own central heating cover, it is your choice, keeping with British Gas (for example) is fine. TOP

The original Air Probe Sanitizer is made of extruded aluminum and all stainless steel connectors. It can be manufactured to fit any size air conditioner. There is no HVAC system which cannot use the original Air Probe Sanitizer. (top)

Radiant heating minimizes temperature swings, eliminates cold pockets of space, and can be used to "zone" a system, sending heat to areas that need it most. Hot water boilers for radiant systems are available with efficiency ratings as high as 95% to provide efficient and reliable heating.

In many cases an existing domestic water heater will do the job. If the BTU rating of the heater is matched with the BTU requirements of the space to be heated, one properly sized unit can provide both space heating and domestic hot water. A boiler is normally not necessary unless the heating requirements exceed 300,000 BTU's. In these cases, a simple mixing valve is designed into the boiler system to provide lower temperature water to the radiant floor.

Yes. It is about 15-20% cheaper but it will depend on the heat source used to heat the water. The new condensing boilers are a lot more efficient when working at low temperatures and have lower return temperatures which helps the condensing process. this expanable content box is made using a free javascript from flooble | Avatars

The underfloor heating pipework is easier to install than radiators, as you have all the information about pipe centres and pipe lengths given to you by us. The connection is simple as you just have to zone it like heating and hot water in a conventional manner or UVHW. See our pack instructions for more details. this expanable content box is made using a free javascript from flooble | Blackjack Tutorial

Ordinarily the radiant tubing must run at a lower temperature than the baseboard. This means that a mixing valve is used to provide a lower temperature for the radiant heating tube. It might be possible to avoid the expense of the mixing valve if the baseboard can be run at a lower temperature and if you select a radiant tubing with a high temperature rating, but the situation will not be ideal.

When you're aware of the advantages, maybe you can find a house you like that already has hot water baseboard heat. If you are having a new home built for you, ask the architect or builder to specify hot water baseboard heating. If you are modernizing a home that has hot air heating, you can leave the cooling system in place but replace the furnace with a boiler, piping and hot water baseboard radiation. No.

Radiant heating provides superior comfort and savings over standard space and water heating systems. Because of its many benefits, radiant heating can also increase the value of your home. It spreads heat more evenly around the room, eliminating cold spots and cold blasts of air from registers. It is a steady, even source of heat. Rooms with vaulted ceilings are easier to heat and homeowners have more flexibility in room arrangements without concern for blocking vents.

Though radiant technology works with virtually any hot water heat source or fuel (Oil,Natural Gas,Propane). Radiant heating includes two primary components: While conventional heating systems rely on air circulation to distribute heat, radiant heating takes advantage of the fact that warm air rises. Installed beneath a home's flooring, it radiates heat upward and outward, spreading warmth and comfort throughout the room.