Answer: OPC (Optical Power Calibration) errors are related to the drive trying to test how strong to make the burning laser. If you recieve this error, the piece of media you are using may have problems. Once the error occurs once on any piece of media, click past the error messages. This will return to the burn screen and eject the media from the drive. Insert the SAME blank media again, then click refresh. The status in XCopy should change to green and give a message of ready to burn again.

Below is a list of the main error messages you will see while searching the Wayback Machine. If you see an error message that does not have the Internet Archive Wayback Machine logo in the upper left corner, you are most likely looking at an archived page or the live web. Failed Connection: The server that the particular piece of information lives on is down. Generally these clear up within two weeks. Robots.txt Query Exclusion: A robots.

This error message means that a Cyclic Redudancy Check failed during some operation, most likely while gzip'ing or un-gzip'ing a file. Possible causes of this error include an incomplete gzip operation, and hardware failure. A brute-force way to recover from this error is to remove the rdiff-backup-data directory. However, this will remove all of your past increments. A better approach may be to delete the particular file that is causing the problem. A command like: will find the failing file.

The Fatal Error is a general error message. More specific information what caused this is available in /tmp/XWin.log. Please check the common error messages in the Section called Error and Warning Messages. If you're error is not mentioned proceed with Q: 7.4.

It means that the recorder is unable to calibrate laser power for the disc. Try different media. If that doesn't help, get the recorder checked.

In very rare occasions the pressure sensor could fail. But usually, this means that you are living near the coast or near sea-level and there is a high-pressure weather system in the area. These conditions can cause the the pressure sensor on-board the AFC-877 to sense an altitude below sea-level. In the v1.0 revision of the firmware, if the Power On Self Test senses that the pressure is below sea-level, it will report a failure of the pressure sensor and halt the processor.

See /waffle/docs/network.doc , 'Managing UUCP and USENET', or Ian Taylor's UUCP Internals FAQ, posted to news.answers, for details.

If you get the error 'Installshield 1628: Failed to complete installation', when trying to install an Agentel client/agent, it means that the user account that you are using to run the installer, has no local administrator rights (e.g. a basic domain account).

with certain calls, you probably have forgotten to mark a 'non call center call' differently in your Axxium flow. So, a call center disconnect is not called for calls that were never connected to the call center.

The failures are software upgrades to the modem. These upgrades are made available to all modems, but your modem make and/or model does not need it.

Ensure that you have Internet Explorer 4.0/5.0 installed in your computer and in the "Configuration Wizard", change the website address to http://www.altavista.com/.

Owing to increased virus activity on the 'Net, some email service providers are stripping any attachment that looks like active content, which unfortunately includes our subscription file. If your .rps file is 0 bytes in size or is empty when you open it in Notepad, we will need to make alternative arrangements for getting it to you. In order to install your subscription, Subscription Manager needs to communicate with our server.

I worked around the problem by ignoring it; in pg_hba.conf, #local all all ident sameuser #host all all 127.0.0.1 255.0.0.0 ident sameuser local all all trust host all all 127.0.0.1 255.0.0.0 trust host all all 0.0.0.0 0.0.0.0 reject A Short introduction to pg_hba.conf can be found in Bric::DBA, and it is more thoroughly documented at http://www.postgresql.org/docs/current/interactive/client-authentication.html.

The drop folder is full. Please empty the drop folder (C:\Program Files\PortListener\Drop), or contact EntechPlus support.

This error occurs when a command is trying to write to stdout or stderr (for example, an "echo" command or an undefined variable in your .cshrc file). Another reason for the error is when your account on an NCSA system is terminated and goes into restricted mode (see section on Account Termination), you will not be able to use scp to copy files from that system to your home machine. If you try, you may see messages like the following: Write failed flushing stdout buffer.

Q0045: I see entries in the log that mention two different IP addresses for the same connection. Why is this? For example: