Since the high-quality sound reproduction is inherent to the digital technology being used, the quality of recordings and/or duplications should not be affected by the type of deck being used. As with CD players, the primary differences between lower-cost portable DAT decks and more expensive rack-mount decks are the features. Don't be fooled by the size of portable decks. DAT is digital technology so the quality is in the technology and not in the features or size.

Absolutely. There are optional light mounting brackets that you can bolt directly onto your roof rack to brighten any trail. Here's a suggestion: mount lights on all four sides of the rack to give your vehicle complete illumination. We are presenting you with a large dose of information, so it's understandable if you're feeling a bit like baggage handler on his first day of work at O'Hare Airport. You are in luck, though. We have a cure for information overload: give us a call.

When you want to mount the fence atop your concrete pool apron, for example, you can use floor flanges on the posts. These are bolted down using lag bolts and anchors which are available at any hardware store. You'll need four 3/8" x 2" bolts per post. It is not unusual to have an angle other than a 90 degree corner. You can use a corner post or a line post, depending on the angle. Basically, anything wider than 90 degrees, use a line post. Less than 90 degrees, use a corner post.

DAT decks are categorized as consumer decks and pro decks. The main difference between these two is that consumer decks put an automatic copy protect code (called SCMS - Serial Copy Management System) onto the DAT while pro-decks do not. Of course, pro- decks are more expensive than consumer decks.

The RaXXess UNS-1 Universal Shelf works well and is available from many dealers. It is usually under $20. You need to remove the four rubber feet from the bottom of the synth module. You can remove and use the two innermost screws that are on the VL70-m to mount it to the tray.

All switches except the AV-2, AV-4, SV-2 and SV-4 can be located in a rack using an optional rack mount kit. The SV-Pro series come supplied with a rack mount kit as standard.

The rack was designed to mount on the front of the vehicle; however we do have customers who mount it on the rear. If your needs call for mounting the racks on the front and the back of the vehicle, we encourage the customer to take a careful look at their state DOT vehicle length requirements before ordering. If capacity requirements are highlighting the need to carry more bikes, you might want to check out our InterlockTM interior bike rack.

Answer: A rack-mount console is an all-in-one flat-panel monitor, keyboard and mouse (typically touch-pad) device, that gets rack-mounted in a standard (19") server rack. When not in use, the flat panel display folds down so that the unit occupies minimal rack space (typically 1U to 2U, 1.75" to 3.5" in height). To use the rack-mount console, the user pulls it out like a drawer and tilts the flat panel up to expose the keyboard and touch-pad and to view the monitor.

Yes. The Radial J-Rak will allow as many as 8 direct boxes to be rack mounted in two RUs. The J33 also mounts in the Radial J-clamp for secure mounting to a desk or rig.

Preamps in most small portable equipment are not very good. Particularly when you want to use professional quality microphones which have balanced outputs and need phantom power to work. A quality preamp like the PMP can provide above requirements and a much better adjustment range when you set your levels. Like independent 21mm knobs that will allow finer volume adjustments.

We make a tail light rack bracket that fits all of our tail lights except the Blinky 1, available here [#3108 detail page].

Is the Savage-1 a truck mount? In a word, YES! It's ALL truck mount, buddy! It sports all the elements you'd expect in a truck mount, from heavy-duty design to extreme heat and high flow. It's NOT a portable, but its unique modular design does dangle the tantalizing prospect of having both a truck mount and a portable in the same convenient package. Most of the time it'll thrash dirt and grime from the convenience of your van.

We can accommodate any size rack mount or Mid-Tower case, but our collocation plans generally provide for a 3U rack-mount or a 21" tall x 8.5" wide x 19" deep Mid-Tower case. Please contact sales@sprocketdata.com if your server is outside of these specs.

The rack-mount brackets are attached to the sides of the unit with three screws each. With a Phillips screwdriver, the brackets can be removed easily.

The width of the Mixer Station will allow for rack mounting however, the nature of the front and rear panel prohibit it, unless severe mechanical modification is undertaken.

You are encouraged to take the exam no later then August of the year prior to the year you intend to matriculate. Interviews cannot be granted until your DAT scores are received.

Not for instrument building. If you can't justify the expense of a drill press, see if there's one at your local technical school or high school shop you can use. There are no good bandsaws smaller than 14". We recommend saving your money and waiting until you can afford a 14" bandsaw. There's a huge difference in quality, and in the amount of work you'll be able to do, once you make that step up to a 14" saw.

The can pulser is an add on unit for the rife crane systems it allows one to access the 11.78 million

It can be moved, but it is not portable. The monitor weighs about 75 pounds. The arm is clamped to the back of a desk or table and the screen rests on the surface.