The external input connections on the rear of the unit are designed for an MPEG2 processor that is very popular in Japan and was scheduled to come to the US. So at this point, there is no US made component that you can connect, short of a 6-channel separate processor that you can use for this port. At the present time, please ignore that section of your AV receiver. Currently, only the RX-Z9 and the RX-797 Stereo receiver are capable of accommodating a graphic equalizer.

To connect the audio output from the computer to the AV receiver, you need a stereo mini-plug to a stereo RCA pin cord. Then connect the line-out from the computer sound card to an available audio input on the receiver. Select the input and adjust the volume output from the receiver.

To get audio from your TV through your AV receiver, please connect stereo audio cables from an available AV input on the rear of your receiversuch as D-TV/LD or CBL/Sat. Then refer to your TV owner's manual for more information about audio output to an amplifier. You may have to turn off the internal TV speakers in order to get any output from the TV into the AV receiver.

Time Scan is advanced Time Attendance recorder and provide following communication inputs and outputs: Wiegand output. In case you intend to install TimeScan in existing RF proximity card network, wiegand output provide you option to connect timescan output to Controller. Hence you can achieve fingerprint security without disturbing your existing network. Relay and Door options: TimeScan provide NO, NC and common contacts along with Door sensor and Door exit button.

Yes, many Yamaha AV receivers are stable down to, but not below 4 ohms. We recommend that you use only speakers with a minimum of 4 ohms. Also, please make sure that the impedance selector switch is set to the correct position as recommended by the owner's manual.

You typically have two options when connecting a powered sub woofer. Input (1) on the rear of the sub woofer would be used when connecting the sub woofer to the receiver using speaker wires. You would then connect the main speakers to the opposite end, or output or the sub woofer to the main speakers. Option (2) would be using RCA line level output jacks, input (2) on the rear panel of the sub woofer directly to the single sub woofer output on the back of an AV receiver.

In most cases, your TV may only have one set of video inputs. If this is the case then you are limited to the amount of video product that you can connect to the TV. By connecting all your audio/video components directly to the receiver, you would only have to use one video cable from the receiver to the TV. This in turn simplifies the connections, which makes video switching easier.

There are four "C" relays (aka terminal outputs) on the bottom of the VA-6000S Base Unit. When a Sensor is triggered, you have the option of activating an external device hooked up to one of these dry contacts (in addition to playing the message alert). The four terminal outputs (labeled NO.1 -> NO.4) correlate to message Zone #1 -> Zone #4 on the Speaker/Receiver. Note: These "C" relays do not provide power but function as a switch.

No. This piece is primarily aimed at the keyboard and similar sources. If you need fully balanced inputs use the SM 26S or the MLM 82S. However, the SM 82 outputs are balanced.

This rear panel connector can be used to insert modulation signals onto a carrier. In conjunction with modes such as AM, FM, SSB, Ext Mod can even provide communication signals at the SIG OUT connector.

A decoder converts an MP3 file into a WAVE file. This is the process most CD burning software goes through in order to burn your MP3s onto CD.

If your current receiver has no subwoofer (RCA) line level output, you will need to connect the subwoofer to your receiver using speaker wire connections on the rear of the receiver. You first need to take the speaker input from the subwoofer to the A or B speaker terminals on the rear of the AV receiver. Then take the speaker outputs from the sub woofer and connect to the main speaker terminals inputs.

In Logic Platinum each sidechain capable plug-in (i.e. each plug-in with a Side Chain popup menu in its interface) can use Tracks, Inputs and Busses as sidechain inputs. In other versions of Logic sidechain input is limited to Tracks only. These are the only possible sidechain inputs.

Yes. Simply turn off the internal audio in the user interface, then connect the line out connections on the back of the unit to external speakers. The VSX 5000 must have speakers connected in order to activate Polycom StereoSurround.

Yes, the number of available MY expansion slots on the Yamaha device (and the DC power requirements of the 6416Y2 card from the host) determine the number of cards that can be used at one time. See the 6416Y2 card page for additional information. Links: Yes, two models of the 6416dio are available, one with DB25 connectors which can terminate as XLR for AES3 and a second with BNC connectors for the AES3-id format.

For best results, ensure that your QuickTime sample rate settings are set to the same sample rate as the audio file you are playing back. This is done from the Control Panel/Sound /Sound Out dialog settings on the Macintosh, and the Control Panel/QuickTime/Sound Out settings dialog box on Windows platforms.

The WX5 is the latest and current model wind controller from Yamaha. It was released in 1998. It is the first Yamaha wind controller to feature a MIDI OUT connector directly on the body of the instrument and optional internal battery power (which makes going wireless a possibility). It also has the most MIDI features of all the Yamaha wind controllers. The standard color is black and gray. Early on, the WX5 was available in blue marble and pearl white by special order.

The WX7 was the first wind controller offered by Yamaha. It was released in 1987 and is now out of production. The WX7 was an excellent MIDI wind controller. Some people prefer it over later offerings from Yamaha- some don't. It includes a set of pots to adjust the feel of the instrument, and a set of DIP switches for various configurations. These make it highly customizable, but it can be difficult to set up if you are new to this.

Quadradial jacks are basically a direct take-off of the FM detector circuit prior to the filters that remove the stereo subcarrier signal components at 19 and 38 kHz.