Depending how old it is, the thermal couple may need to be replaced. If the knob is getting stuck, there’s a good chance the safety pilot may need to be replaced.

Since Blaze King gas appliances are designed to run without electricity, they are millivolts systems. When the pilot is lit, the flame makes contact with the thermocouple or thermopile, creating less than ? of a volt of electricity. This current is designed to keep the valve open and allow gas to continue to flow. When the pilot goes out, the current ceases and the valve shuts down. See similar questions...

The most common cause of pilot outage in gas fireplaces is actually a weak pilot flame. This usually indicates debris and deposits have built up causing weak fuelflow. This would indicate the Fireplace should be serviced by your Service Provider. (See the dealer locator for the nearest service shop in your community, state or Province). Back to Top See similar questions...

A pilot light will burn 800 to 1500 BTUs/hr. Your monthly gas bill should include your exact cost per "therm" (100,000 BTUs). Based on this rate you can calculate the cost for your area to operate a pilot light. See similar questions...

Do NOT attempt to relight the pilot light yourself. Please call the office at (812) 330-1411 and make a maintenance request. See similar questions...

On some computers, when using an ATA6 hard drive, the LED light will stay lit. This is caused by the difference in voltage running through the pins. Although the LED light stays lit, the drive is working and functioning properly. If you are experiencing this and can not tolerate the light staying lit, please contact us to replace your drive with an ATA5 hard drive. See similar questions...

If your pilot will not light after following these instructions, please see your owner's manual or contact your nearest dealer for assistance. See similar questions...

Answer: A 24-hour maintenance company is on-call. You will be provided with telephone number at check-in. See similar questions...

If a payment is received after the due date, it may not have been credited to your account before the bill was processed, printed and mailed. If this occurs, please call the call center or billing department to ensure payment was received and ask for the actual balance. See similar questions...

Iris recognition technology is strictly voluntary – just as it is now with any identification card kits that may be used with children. Participants agree to enroll, thereby eliminating privacy concerns. The user voluntarily decides to participate in iris recognition for authentication by looking at a digital video camera from about 5 – 10 inches away from the camera. The technology cannot work without the explicit cooperation of the end-user. See similar questions...

Institutions that fall short of meeting NCAA standards during the certification process must identify opportunities for improvement and are given ample time to implement them. Institutions that neglect to make an honest effort to improve can face serious consequences, including ineligibility for NCAA championships and removal from the NCAA. See similar questions...

Charities in the UK fund more research than both the NHS and the Government together. It isn’t something we are happy about and we are working to increase the amount spent on research. We are sure that you would agree with us that it would be a backward step if we were to stop what we are doing, while we wait for the government and the NHS to fund research. See similar questions...

It is important that you involve your GP and other health advisers in any lifestyle changes that you intend to make before you start. This is a partnership with you and your health advisers, we need to work together to get you the best plan for health. Please remember, we do not diagnose a health condition and we do not prescribe treatment. See similar questions...

If the error message "Required OpenGL functionality is not available" appears, OpenGL can be emulated with the “opengl32.dll”, so that the DPV also runs with graphics cards that don’t yet support this standard. The .dll must be copied into the bin directory of the application. See similar questions...

Remember that OpenGL is a state machine. You'll need to do something like this: glEnable(GL_LIGHTING); // Render lit geometry. glDisable(GL_LIGHTING); // Render non-lit geometry. See similar questions...

First, be sure that the end of the incense stick is glowing orange before blowing out the flame. This usually does the trick. But as frustrating as it is, sometimes even the best incense refuses to stay lit. Although this is uncommon, it does happen on occasion, and is not an indication of "bad" incense. We have found that even some of our freshest incense will not stay lit. It may be that the oil used to make the incense hasn't had quite enough time to dry. See similar questions...

It may be that your cylinder is malfunctioning, cylinder has a leak, or the pilot is clogged. Please see steps below to troubleshoot. Note: Regular maintenance is critical to the successful operation of your patio heater. Check to see if you can light it manually. If the unit lights manually but not with igniter, service or replace igniter switch. Ensure that there is no air in the gas line. See similar questions...