Wash it at least once a month with one of the many auto wash liquids, paying special attention to removing winter salt deposits from the undercarriage. Some motorists don't thoroughly rinse off dirt before washing a car; any dirt rubbed into the surface can cause scratches. Take the time to run the wash mitt or rag along the inside bottom edges of the doors, hood, trunk or hatch; those areas trap moisture and dirt and can cause premature rusting.

You should treat the protection film shield the same as you normally do to the rest of the car's paint. Just make sure it's fully dry from installation and all edges are properly adhered before doing so (no flapping edges). High pressure washes will not affect the film kit as long as you avoid spraying the high pressure nozzle directly at the protection films edges from a ridiculously close distance (this isn't good for your paint any way).

This is a matter of individual taste and preference. However, in general, the following guidelines are considered basic: Never use a product with abrasives/and or detergents on a clear- coated car, especially one that is new. A rotary buffer can achieve results that hand waxing never could, however it is a skill that must be mastered as incorrect use can also damage the paint/clear coat.

There are no exact specifications. When the water beading and the finish appearance indicate that the wax is gone, re-apply.

After two weeks, you can wash, wax and polish the motif the same way as you maintain your car regularly. In fact, you can use a mild abrasive polisher to smoothen the film edge of the motif to an extend that you cannot feel any edge at all.

The age of computers has even touched the car wash industry. Every vehicle is measured precisely by multiple sets of electric eyes that measure the length as well as the height of each vehicle. We have created installed new computer system that has given us greater control over the car washing process. For example we know exactly where the tires are so we can apply exactly the correct amount of wheel cleaner to just the tires.

The sealants and waxes we use won't streak the outside of your windows. However, grease and oil can get trapped underneath your wipers, which can cause the rainbow like streaks you may see on your window.

No. The wax itself won't streak the outside windows. However, grease and oil from the road spray can get trapped underneath your wipers, which can cause the rainbow like streaks you may see.

You may wash your vehicle immediately, but we recommend you wait 30 days before using any wax. Auto Crafters will wash your vehicle before it is returned to you.

soon as you get your custom painted parts, you can install them on your bike and wash the bike. We ask that you NEVER use a dish soap like Dawn, Joy, etc. These products will strip the polish and wax right from your bike! Always use a specific automotive grade soap (Mothers, Meguair's, etc), and remember, always wash your bike in a shaded, cool environment, not out in the mid-day sun! The general rule of thumb for waxing is 30 days cure at 70 degrees.

Actually, you can wash and wax right over the lettering the minute it's applied. There's no required drying time for the vinyl adhesive. The adhesive will continue to become more aggressive over time with exposure to heat from the sun. The vinyl requires no extra preventative maintenance once it's on your boat other than normal washing and waxing.

You will be greeted by our friendly, trained staff of car wash professionals. All you need to do is put your vehicle in neutral and turn off your break when asked, and relax as we guide you through our simple process. We clean the exterior of your vehicle with gentle, super soft cloth washers and mild cleaning solutions. Your wheels and tires will be cleaned, and your vehicle will be rinsed and gently air dried ? all automated by our computer controlled, 3 minute EXPRESS car wash.

Yes! Most auto manufacturers caution against automatic washes that use acids or tire brushes on polished aluminum wheels. At ECO, our acid free, foaming wheel applicator is a highly concentrated cleaner and de-greaser that will not stain or scratch your wheels or tires. This highly foaming applicator sticks to your wheels and tires to ensure 100% clean.

We do not prep your wheels before they enter the car wash. We have state of the art foaming wheel sprayers. The foaming wheel applicator is a highly concentrated cleaner and de-greaser. This foaming applicator covers 100% of your wheel and tire, ensuring a clean and bright result.

You can wash your vehicle as often as you wish. Keep in mind that using soap or car wash detergent can, over time, cause a build up on the paint surface that causes it to appear dull. This build up will need to be removed through a comprehensive process included in a deluxe detail that should be scheduled twice a year. We recommend that you only use proper car wash soap that is well diluted in cool or lukewarm water - never hot water.

DO - Wash the vehicle by hand with cool water and a very mild car wash solution using a soft cloth or sponge. Always use clean fresh water. Wash your vehicle in the shade. DON'T - Do not use a commercial car wash. Stiff brushes or sponges could mar the finish and damage the surface. Do not "dry wipe" your vehicle. Dry wiping can scratch the finish. Do not drive on gravel roads. Chipping the finish is easily done in the first 30 days.