These models are designed to work with an external internet connetion, such as a an external ADSL or cable modem, and so are ideal for using with a Telstra Bigpond or Optus cable service, using the cable modem supplied by Bigpond/Optus. Please see the WAN FAQ. The DrayTek Vigor models which have a built-in ADSL modem are hardcoded to apply router, firewall and VPN to the ADSL interface (and ISDN interface, if included).

We will use cables similar to those running under the Cook Straight, which were installed in the early 1960's to bring hydro power from the South Island to the North. The bipole HVDC cables are waterproof, salt corrosion resistant, solid plastic polymer, insulated copper with high mechanical strength. The cables are about 125 millimetres in diameter and buried over one metre under the harbour floor. See similar questions...

There is no required length of a cable for an Amplifier to be active, a standard cable comes with the purchase. Please consider each model has different length of cable. See similar questions...

c) Check the IP address captured. Go to Start > Run > type cmd (Win2K/XP) or command (Win98/Me) > in the dos prompt type ipconfig to check your computer’s IP, it should be in the same subnet as the router. I was able to ping the IP of the router, but I was not able to access the web configuration page 192.168.1.254 For Internet Explorer, click Tools, Internet Options, and then the Connections tab. Make sure that Internet Explorer is set to Never dial a connection. See similar questions...

No. UPSilon 2000 v2.0 is an old version and cannot support Windows XP operation system. If you are using version 2.x or earlier, kindly contact our service for a special upgrade price. The "Bucking voltage" means that the UPS is stepping down high voltage to levels that are safe to your system. I'm running UPSilon2000 on WinXP on SP2. After a reboot the following error occured : the icon in the taskbar showed that it had no connection to the UPS. See similar questions...

If the adapter cable is used for charging and cycling batteries from 2 to 12 cells the length and gauge of cable is not critical. Only 18 gauge or heavier and 36 inches or shorter cable should be used with "V" device. This is necessary because the second four digit reading of the "V" device is taken under heavy 1000mA load and thin long cables will have a large voltage drop. This will result in voltage at the battery being higher than at the Alpha4 port jack. This will cause flashing V. See similar questions...

wire FAMS networks: Screened twin twisted pair 22AWG Type 1 data cable (RS part no. 367-959) or Telephone cable, type: CW 1308 twin pair (RS part no. 368-413) wire FAMS networks: Screened single twisted pair 22AWG Type 3 data cable (RS part no. 360-649) or Telephone cable, type: CW 1308 single pair (RS part no. 368-407) FACT networks: Belden 8451 - single pair 22AWG shielded (RS part no. 360-649) or Telephone cable, type: CW 1308 single pair (RS part no. See similar questions...

The recommended VGA cable distance is 5 meters maximum without ghosting and degradation. Normally, the cable length is based on driver capacity of your VGA card. If you need longer VGA cable, please use VGA extender to accomplish your applications. The recommended keyboard or mouse cable is 10 feet maximum without degradation. Normally, the cable length is based on driver capacity of your motherboard. See similar questions...

Nowadays, EURIDIS is the only international standard working with twisted pair cables for the remote reading of residential meters. The basic solution uses a field bus for communication. Nevertheless, because it may be difficult in some cases to install the two-wire EURIDIS cable, new AMR technologies have been designed over the last few years. See similar questions...

The basic unit ships with one microphone and a 30-foot conference link cable. An optional 50' cable is available for the first connection to the codec. See similar questions...

All Fostex recorders including the VF-16 conform to SCSI-2. This is regardless of the type of SCSI connector with which it is equipped. In the case of the VF-16, its SCSI connector is called mini 50-pin. Connect the signal to the VF16(2), assign them to any two tracks and setup the mixer for record input monitor. See similar questions...

You will need a standard usb cable (the one that is included in the box when you buy the phone). Because you are going to use a usb cable you have to install drivers for this cable. You can find this drivers at the downloads page If you do not have this cable you can buy it from us. For now go to contact site to ask us for the cable. You can also buy it in every electronic store and ebay. It's often the same cable as used to connect digital (video) camera's to a pc. See similar questions...

All A-Net products require unshielded twisted pair (or "UTP") cables that are Cat-5e or better. Do NOT use shielded cables under any circumstances. See similar questions...

In a word: No! FutureFLEX fiber uses the same type of glass and is provided by the same suppliers as conventional fiber. However, because it's aerodynamically designed to be blown in, FutureFLEX cable looks different . . . it's thinner and lighter, typically 1/40th the size. There's no pulling force with an air blown installation, which eliminates the need for bulky strength elements and fillers. See similar questions...

On all models (except CHM190 &300DT), the CAL mode allow users to periodically check the unit, to ensure that it is still operating within specification. Whenever the unit is to be checked for accuracy a reading should be taken from the same point, noting the result and date in the table. If the reading is outside of specification, you should contact Suparule by email: info@suparule.com. See similar questions...

If the above link doesn't work, start at the Olympus America web site, go to the Digital Camera Section, and then look in the Support section for Brochures & Manuals. Olympus Smartmedia/xD USB Reader/Writer (skip the serial cable and get this or the one below, MUCH faster uploads) Olympus Emporium (direct sales from Olympus) has these and many other products (e.g., printed instruction manuals) available at high prices. See similar questions...

The PSC cable is a pure silver 75-ohm coax cable with RCA terminations. Unlike many “video” cables on the market today, the PSC maintains its 75-ohm impedance from tip-to- tip. Our special RCA terminations actually maintain the 75-ohm impedance critical to quality composite and component video connections as well as digital coax connections. See similar questions...

Yes. The specifications for composite video, component video and digital coaxial cables are EXACTLY the same! Since our PSC cable maintain a 75-ohm impedance from tip-to-tip, it is the perfect cable for each of these connections. For component video applications you will need three PSC cables (which we offer on our website in special component cable discount packages). See similar questions...

A suitable cable for connecting both types of reader to a Feedback Terminal is Belden 9536 (RS part no. 382-453). See similar questions...