When the door is open measure from the inside face of the opening door to the outside. This is the distance between the handle on the inside and the handle on the outside measured in millimetres. This needs to be reasonably accurate (within 3mm say).

When installing our deadbolts you want to make sure that your door is somewhere in between 1-3/4in and 2-1/4in in thickness. If your door is not in that range please call customer service. When installing our standard doorsets you want to make sure that your door is somewhere between 1-3/8in and 1-3/4in Note that extended spindles are required on passage locks that will be used on thicker exterior doors. These are offered by special request only.

StockerYale's low power laser line projectors have a pseudo-Gaussian widthwise intensity profile analogous to that of many gas lasers. The thickness (or width) of the line is measured at the 1/e^2 points of this profile. A chart of LINE THICKNESS VS PROJECTION DISTANCE can be found in many of our Laser data sheets and brochures. In order to guarantee accuracy, the values measured were carefully taken using a Merchantek beam profiler.

Once the 10+” of wool layers are stuffed into the cotton cover, the final thickness of the Cuddle Ewe Underquilt is approximately 3”. With use, the Cuddle Ewe Underquilt will compress to a thickness of about 1.5” to 2”. This is very normal and to be expected. Once the wool has compressed, there is nothing that can be done to re-fluff it, but it will still be comfortable. With proper care, you can maintain the Cuddle Ewe’s loftiness for a long time.

If your van comes with two side doors, always measure the door on the curb / passenger side because it's usually larger than the door on the driver side. As long as you have 30" or more on the door threshold where the ramp will be loaded, you'll be OK to use our ramps.

DOOR WIDTH - Measure the distance between the inside point at the jamb of one side of the opening to the other. Take this measurement at several places along the jamb to insure a square opening. DOOR HEIGHT - Measure the distance from the floor to the underside of the lintel at several places to insure a correct reading.

First open your out-swing door, which will most likely be a back door. With your door open, measure the swinging door ( width and height ) not including the lip of the door. Then simply round up to the next inch. (Example: the out-swing door measures 33.5 inches wide by 75.5 inches high will equal a 34" x 76" call size.

For applications where plating thickness is critical we periodically measure plated layers using a process called " x-ray fluorescence". This non-destructive method is very precise for measuring the actual metal deposition on an object after electroplating.

Measure Out-swing storm door or In-swing core door, (measure just the swing door). Add two inches to the width and one inch to the height, then round up to the next inch. (Example: Out-swing storm door measures 31.5 inches wide by 74.5 inches tall, you need a 34" x 76" call size.)

Since edge thickness is a function of lens power, centre thickness and curvature of the front and back curves (all inter-related) the edge thickness is influenced by the following features:

The model name label for all HealthSmart™ Beds includes the thickness designation of the top after the model name. For example - Haverville™ Luxury Firm 1X. The model name label is sewn into the lower right side of the HealthSmart™ Top. this time, Simmons manufactures HealthSmart™ Beds with a specific thickness of removable top. Higher end models will have thicker tops as part of the luxury step-up within the line.

Early pedometers were mechanical and used a moving lever arm to count steps. Electronic pedometers now detect movement through a spring loaded, counter-balanced mechanism that records vertical acceleration at the hip. Pedometers measure the number of steps a person takes throughout the day.

Registering early costs less and will guarantee you a seat. If you show up at the door, the ticket price will be higher, and we cannot guarantee that you will have a seat. It is recommended that you sign up in advance. In all honesty, there's a very slim chance that you'll be able to get a seat the day of the event.

If an ST says the phrase, "this is a door," he means that there is a greater possibility in the situation you are about enter that your character will be killed. None of our plots aim to kill people, but sometimes players can be very unlucky throwing chops. We respect that players work hard on their characters and do not like to see them taken away by a situation they may feel let down by.

Measure the width and length or diameter of the table you'd like to cover. Measure from the table top down to where you'd like the tablecloth to drop. Add the drop twice, once for each side:

A prospective, randomised, controlled trial of 92 patients with full-thickness pressure ulcers set out to compare the efficacy of an alginate wound dressing with an established local treatment with dextranomer paste. During treatment, a minimal 40% reduction in wound area was obtained in 74% of the patients in the alginate group and in 42% of those in the dextranomer group. The median time taken to achieve this goal was four weeks with alginate and more than eight weeks in the control group.

Foam cores are available 1" foam to 12". Typically SIP foam thickness matches out to dimensional sizes then the OSB adds another 1" total.

The thickness of the fiberglass varies. The parts that require assembly of more than one component piece are usually thinner at the mating areas, but the overall piece becomes stronger when the pieces are bonded together. Some parts such as inner fenders and outer fenders do not need to be too thick. In the assembly process sometimes the thickness is a deterent and the parts must be ground to get them to fit properly.

The cover itself is only 1/2 inch thick and as a result, protrudes downward approximately 1/4" below the top edge of the side rails (except for the spring loaded lock handle which comes down approximately 3 inches on the Driver's Side).