If you are using PhotoShop CS and have the appropiate raw file plug-in, YSI will import Camera Raw Files. The Raw file conversion will only engage when you export a finished layout direclty into PhotoShop or Batch process all files as PSD's. Each image within a aperture will be prompt for conversion as the layout is built.

there is only one TCP/IP stack, the complete network information must be configured from the Global zone. The Global zone administrator can add one (or more) default route for each subnet, the kernel will make sure that the right one is used for each non-global zone depending on its IP & netmask.

Not yet but it will be eventually. A Sun engineer has started working on this. More information. If you can live with an unsupported procedure, have a look at this lab.

Snoop works by talking to the “DLPI” interface that itself contacts the appropriate NIC drivers. To implement the network isolation feature of non-global zones, access to DLPI and the lower levels interfaces is disallowed.

Yes. Just use the “ifconfig” command from the Global zone. Don’t forget to also update the non-global zone’s configuration if you want the change to be persistent.

Yes! And no… The reource capping feature of Solaris Resource Management allows one to set an upper bound to the amount of RAM used by a certain project. By creating projects inside a non-global zone and setting the rcap.max-rss project parameter, you can limit the amount of memory used by all the processes belonging to that project. So it is not a zone-aware feature but it can be used within non-global zones through the use of projects.

Yes, as long as it doesn’t require the exporting of a new disk device to the non-global zone. See Question 2.5 & Question 3.7

Configurable only from the Global zone. A restriction is that IPFilter cannot be used to restrict access between 2 non-global zones. The loopback interface is used for that purpose and IPFilter cannot be used to inspect packets goign through that interface. See question 3.2. Starting with Solaris 10 06/06, Zfs is available as a standard supported feature. A siple HOWTO document describes few of the possibilities of integrating Solaris Zones & ZFS. Read the document or go to the sun.

Yes! The standard Resource Management features have been extended to zones. The Fair Share Scheduler is a scheduling class controlling the proportion of CPU time that a certain entity may use. The administrator of the Global zone is in charge of setting the new ressource control zone.cpu-shares to assign a number of shares to each non-global zone ( the Global zone is assigned 1 share by default ).

Yes! The Resource Management model being hierarchical, the first thing to do is to assign a number of shares to each non-global zone ( See 5.1 ). Within the non-global zone, the non-global zone administrator may now create projects in the standard way to differentiate between workloads running in the same non-global zone. Resource contention between these workloads can be resolved by assigning FSS shares to the projects.

Yes! First create a processor set that contains some of your CPUs ( be careful, you still need some CPU time for the Kernel! ). Then create a resource pool and bind the processor set to it. Finally bind your non-global zone to the same resource pool. All the processes running in your non-global zone will then run on the CPUs you selected by creating the processor set.

After the non-global zone has been installed, all kind of typical identity information needs to be provided. It can be done in two ways: Interactively : the Global zone administrator boots the zone for the first time. A “sysidtool” process ( the same that the one used for a standard installation ) is then launched inside the non-global zone. The administrator needs then to connect to the non-global zone console using the “zlogin -C my-zone” command.

On this page, we'll try to answer some of the more frequently asked questions about roses that we've heard from our customers. When you're faced with uncertainty about what to do with your roses, read as much as you can about roses and ask your gardenings friends for advice. But most importantly, relax -- remember, you're doing this because you want to! Taking care of roses is alot like taking care of anything -- you have to pay attention to them so you know when something is not quite right.

We deal with only bulk chemicals. By importing large volumes of chemicals, we are able to offer lower prices. However, we deal directly with chemical distributors and can help you locate a distributor specializing in the chemicals and quantities you are looking for.

Yes, many fraudulent water treatment devices are being marketed. If a device is being sold on the basis of health claims and is not certified, there are two problems: (1) there is no reason to believe that it works as advertised and the product warranty and replacement parts will not solve the problem, and (2) the device is being sold illegally in California. Here are some questions to ask about any water treatment device that is being sold on the basis of health claims:

Yes, because IntraVUE works on the premise of IP identity, you will have to manually add any device that is not detected. This is useful for full visualization and the topology of the network. Login as administrator and select Add Child from the System Menu on a device that will be the 'parent' of the non-Ethenet device. This adds a new node that is a user node, such as a Device Server (Serial to Ethernet converter).

Yes. Data from Garmin and other fitness devices can be uploaded to the SportsDo portal and merged with your native SportsDo data.

The main question is whether you need to perform the backup from the Global zone or from the non-global zone. You have some enterprise backup software like NetBackup or Legato Networker. Even “ufsdump” requires access to devices which might not be available from the non-global zone. You want to be able to restore your entire zone, not only the data it contains. Main example is Disaster recovery.

The importation of raw materials has already been liberalized. Therefore the importer simply has to proceed to an AAB to open the necessary letter of credit or other modes through which payment will be made. There are, however, regulated items that require clearance from the concerned agency prior to importation, and items whose importation is prohibited. The Barangay Permit is given by the Barangay where your business will be located. The fee is PhP 50.

For .RAW it's simple: just click on "Objects|raw" and select the file you want to import. There's not support for .DXF files.