This is actually one of the most frequently asked questions we get. We get it so often, in fact, that we started playing around with a digital micrometer and came up with this page which gives the thickness of common household items.

Once the 10+” of wool layers are stuffed into the cotton cover, the final thickness of the Cuddle Ewe Underquilt is approximately 3”. With use, the Cuddle Ewe Underquilt will compress to a thickness of about 1.5” to 2”. This is very normal and to be expected. Once the wool has compressed, there is nothing that can be done to re-fluff it, but it will still be comfortable. With proper care, you can maintain the Cuddle Ewe’s loftiness for a long time. See similar questions...

Here are the dimensions of these coins along with the closest matching magnet that we currently stock: US Dime = 0.71" dia. x 0.053" ==> DA1 (0.63" dia. x 0.063") or DC1 (0.75" dia. x 0.063") See similar questions...

The rule of thumb usually is, the heavier the equipment is, the thicker the mat needs to be. If its just elliptical and light equipment, 3/8" mats will work fine. For heavier equipment like commercial treadmills or weight stations, use 1/2" or 3/4". If there is heavy free weights, or lots of traffic, definitely use 3/4". See similar questions...

The thickness of the foam core allows the tape to compensate for surface mismatch between two surfaces. This is most important between two rigid materials. In the case of the acrylic foam tape, the core adds properties such as stress relaxation, plastisizer resistance and enhanced conformability. See similar questions...

Since edge thickness is a function of lens power, centre thickness and curvature of the front and back curves (all inter-related) the edge thickness is influenced by the following features: See similar questions...

The model name label for all HealthSmart™ Beds includes the thickness designation of the top after the model name. For example - Haverville™ Luxury Firm 1X. The model name label is sewn into the lower right side of the HealthSmart™ Top. this time, Simmons manufactures HealthSmart™ Beds with a specific thickness of removable top. Higher end models will have thicker tops as part of the luxury step-up within the line. See similar questions...

Many parts can be more economically machined from tubular stock. However, since the Estimator only knows the basic dimensions of the part, it assumes by default that the part will be machined from solid stock unless a tube wall thickness is selected. The wall thickness should be selected so it can accommodate the minimum and maximum diameters of the part. An appropriately sized aluminum tubular stock must also be available. See similar questions...

A prospective, randomised, controlled trial of 92 patients with full-thickness pressure ulcers set out to compare the efficacy of an alginate wound dressing with an established local treatment with dextranomer paste. During treatment, a minimal 40% reduction in wound area was obtained in 74% of the patients in the alginate group and in 42% of those in the dextranomer group. The median time taken to achieve this goal was four weeks with alginate and more than eight weeks in the control group. See similar questions...

Foam cores are available 1" foam to 12". Typically SIP foam thickness matches out to dimensional sizes then the OSB adds another 1" total. See similar questions...

The thickness of the fiberglass varies. The parts that require assembly of more than one component piece are usually thinner at the mating areas, but the overall piece becomes stronger when the pieces are bonded together. Some parts such as inner fenders and outer fenders do not need to be too thick. In the assembly process sometimes the thickness is a deterent and the parts must be ground to get them to fit properly. See similar questions...

The cover itself is only 1/2 inch thick and as a result, protrudes downward approximately 1/4" below the top edge of the side rails (except for the spring loaded lock handle which comes down approximately 3 inches on the Driver's Side). See similar questions...

Yes, overlays are only 1/16" to 1/2" as a standard. Thicker applications applied only to level. See similar questions...

The stone is available in two thicknesses: ¾ inch and 1 ¼", 2cm and 3cm respectively. Granite flooring tile is 3/8" thick and usually 12" X 12". See similar questions...

Carpetiles are approximately 3/8" thick. Their tough, but flexible vinyl backing makes them easy to cut and easy to install. See similar questions...

Glass blocks come in 2", 3" and 4" nominal thickness because different products and applications require different thickness. CrystaLok windows have an adjustable frame and can use all three sizes, but 2" is the lightest and easiest to install in large windows. REDI2SET windows use 3" block because they come in the most number of face sizes giving REDI2SET windows greater flexibility to fit into existing openings. See similar questions...

Optical thickness or optical depth describes how much light passes through a material. Since the amount of light that passes through a material can be quite small (less than a fraction of 1%) or very large (nearly 100%), optical thickness is based on a logarithmic scale. There are various definitions. When the optical thickness of the atmosphere is measured, the usual definition is that the optical thickness is -ln T, where T is the transmission of the atmosphere. If T is 0. See similar questions...

The "Roosevelt" dime (1946 to present) was issued to honor President Franklin Delano Roosevelt, who was elected to four terms of office and served from 1933 until his death in 1945. Roosevelt was chief executive of the United States longer than any other president, bringing the nation out of the Great Depression and leading it to victory in World War II. See similar questions...

DIME's avatar policy is plain and simple. If a moderator or administrator does not like your avatar, it will be blocked. Afterwards, you do not have the chance to add a new avatar image to your profile anymore. To get a new one, you must send the URL of your new avatar by mail to the DIME moderator desk. The new image will be evaluated - and should it be approved - the moderators will restore your ability to change your avatar image on your own. See similar questions...