LANforge's PPPoE support has been tested with the Roaring Penguin PPPoE server. Here is a short guide to configuring it. Please see your PPPoE server's documentation for more detailed configuration information. PPPD BUG pppd version 2.4.3 contains the following bug: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=298582 It is fairly likely to be broken on your distribution. It prevents pppoe-server from working, but has no effect on pppoe clients.

Different levels of Speed can be set by userid in a product like ServPoET. Maybe you want to charge your users by the hour or minute you could also charge your users by the "byte". ServPoET, offer the ability to roll out Dynamic Service Selection. This option allows you to set up different services and allows customers the ability to log in to them if you've set that up in your profile. See similar questions...

Start the Active Directory Sites and Services Manager (Start - Programs - Administrative Tools - Active Directory Sites and Services Manager) See similar questions...

The DHCP Server Service is configured using "DHCP Manager" that is installed after the installation of the DHCP Server Service. Exclusion - start and end, e.g. 200.200.200.20 and 200.200.200.30, would mean available addresses would 200.200.200.10-200.200.200.20 and 200.200.200.30-200.200.200.100 A message that the Scope has been added, but is not active, would you like it to be active, click Yes. See similar questions...

PPPoE operates at layer-2, the interface that accepts pppoe requests need no IPs assigned (great for security), and must NOT be in bridge mode. The IP range you are assigning to your customers must be within the range of the subnet assigned to your WAN interface. For instance, if you wish to assign your customers IP ranges 192.168.1.100 to 192.168.1.200, you would use the following configuration: Under your pppoe server setup, set it to enabled, and add the IP range 192.168.1.100 to 192.168.1. See similar questions...

All of the configuration information we have, is included with the release. You should use one of the included configuration programs, XF86Setup or xf86config. This is explained in the QuickStart Guide. For further information, you could also read the XFree86 configuration guide (available from http://www.XFree86.org/3.3.5/Config.html), and the manual pages XF86Config(4/5) and xvidtune(1). See similar questions...

Some servers have no facility for this; you may be able to adjust your monitor to correct somewhat. Later versions of XFree86 allow these server options: gamma f set gamma value (0.1 < f < 10.0) Default: 1.0 -rgamma f set gamma value for red phase -ggamma f set gamma value for green phase -bgamma f set gamma value for blue phase See similar questions...

Connect to the router through web browser. Set the broadcasting IP address and Port, select TCP-IP protocol. How to ... If you hear nothing from your broadcasting page, check the 'Tools > Internet Options > Advanced > Java (Sun) > Use JRE v1.x.x_xx for <applet>' option in MS Explorer. If there is no such option or if the JRE version is lower than 1. See similar questions...

PPPoE stands for Point-to-Point Protocol over Ethernet. This is an IETF draft standard specifying how a computer interacts with a broadband modem (i.e. xDSL, cable, wireless, etc.) to achieve access to the high-speed data networks via a familiar PPP dialer such as "Dial-Up Networking" user interface. PPPoE supports a broad range of existing applications and service including authentication, accounting, secure access and configuration management. See similar questions...

You configure each section (numbered 1-10) by pointing DSpy to the proper directory on your network. By putting a shortcut to DSpy in your startup folder, it will start with your TSC client during every boot/login and automatically start tracking your TSC progress. See similar questions...

In the Webmin Servers module, create a new user and give him access to only the Apache Webserver module. After saving, click on Apache Webserver next to the user's name in the list of Webmin users and use the form that appears to deny him access to everything except one selected virtual server. Many other modules can also be configured in a similar way to restrict the access of a user to only certain DNS domains, Unix users or mail aliases. See similar questions...

Yes. We support both Master and Slave zones. When adding a domain into our system, you decide at the time you add it whether or not you want our name server network to act as Master or Slave for your domain. When configuring a Master domain, all of our name servers will be acting as a Master server. When configured a Slave domain, all of our name servers will act as a slave server. See similar questions...

The installation process will prompt you for your Windows CD and will install the SMTP virtual server. Open the node for your computer, right-click the Default SMTP Virtual Server node and choose Properties. Select Only the list below, click Add and add the IP 127.0.0.1. This restricts connections to just the local computer, i.e., localhost. Close the Connection dialog box. In your firewall or router (or both), close incoming port 25. See similar questions...

Installing the Axis 2400 to your PC. Make certain to have all cables plugged in. Power on all units. The network LED shall go on after power up sequence. Assign an IP number. If you are familiar with DHCP you may use that. If not, try to use the arp command from DOS. Find an available IP address (e.g. 192.168.1.55). First do "ping <IP number>" and it shall respond "request timed out", which indicates you have a valid IP number that is not used. See similar questions...

Depending on whether you're running the eBLVD Host or Client software (the Client software is used to connect to a PC running the Host software), you can set up our remote control products to work with your proxy server. Remove the checkmark from the "Automatically detect settings" option & click the "Manual configure" button. Remove the checkmark from the "Automatically detect settings" option & click the "Configure Proxy..." button. See similar questions...

If you have a multiple-user license, you can use any computer that is connected to the network. If you have a single-user license, use the compter where you plan to use CAESY Enterprise programs. Do not use the computer that acts as a server or that has a direct connection to a high-speed modem, such as cable or DSL. See similar questions...