Our tools and equipment perform at speeds of up to 2,300 ft/min. Please keep in mind that this depends very much on the material and the hole size. With a diameter of 0.040", for example, a maximum speed of approx. 250 ft/min can be expected.

By Plane: Fly into either Brownsville (30 miles) or Harlingen (45 miles) Airport. Once you know your flight itinerary, contact the airport shuttle and arrange a no-hassle ride to the island. By car: Drive to south Texas, following the signs toward Harlingen/Brownsville. When you get to the Rio Grande Valley, follow the signs to SPI. DO NOT SPEED THROUGH LOS FRESNOS! Nabbing speeders is that town's main source of revenue.You will know you are here when you have crossed a very long causeway. See similar questions...

SPI means Serial Peripheral Interface. Due to the name one could think that SPI is a "normal" serial Interface. In contrast to the RS232 (+/-12V, asynchronous with start/stop bits, one transmitter, one receiver) the SPI works with TTL-levels, a separate clock line (synchronous) and has a master and an unlimited number of slaves (with only one active slave at a time). Each slave has its own chip select line and two shift registers as I/O interface. See similar questions...

Depending on where you live, our state-of-the-network allows download speeds of 2Mb, up to 16Mb. all depending on how far you are from the exchange the further away you are the less speed you get See similar questions...

Our Segways are equipped with Nickle Metal Hydride (NiMH) batteries good for about 12 miles on a full charge. New model Segways now come equipped with Lithium-Ion batteries that will get you twice that far. Average charge time is roughly 6 hours, but with the built in charge management package, you can just plug it in and forget it. No memory developing, no overcharging, just a simple wall outlet is all you need. As for speed, the segway has three different pre-programmed settings. See similar questions...

The recommended maximum stroking speed for NITRO-SPRINGS is 35 metres/minute; it must be remembered that this is not the cyclic speed of the press. We recommend a maximum stroke rate of sixty cycles per minute. See similar questions...

A number of factors affect the speed and quality of ADSL transmission. Among the causes of poor transmission speed are: The distance and line quality from the NTT central office to your premises. It is a fact that speed generally declines the farther you are from the central office. See similar questions...

The stop's maximum speed is approximately 20 inches per second. If moved faster, the display may require re-calibration. See similar questions...

The moderns stepper motors can reach rotation speed of 1500 RPM. It must be considered that the motor torque curve decrease considerably with the increasing of the step frequency. If we take a screw of 4 mm and we run it at 1500 RPM we obtain a displacement speed of 1500*4mm=6000mm/min or 6 m/min. In practice the stepper motors runs at max 600 RPM because the torque decrease above that values. See similar questions...

The factor that limits operation is the speed at which measurement data can be transmitted over the network that connects the sensors to the Data Logger. This is limited by the speed of the network the ability of the Data Logger to read and store it. Each sensor node has its own microprocessor to control the measurement cycle, provide automatic range changing / diagnostics and network interface. This does not have any practical limitations. See similar questions...

The number of cameras per frame grabber determines the number of fps of recognition. We have had reports of 165km/h recorded. See similar questions...

The maximum data rate is 1 Mbps asynchronous and 10 Mbps synchronous. This number is the result of a mathematical calculation based on the on board oscillator value on the card. Actual maximum data rates may vary depending on cable length, type of driver, operating system overhead, disk activity, etc. The Zilog web site has the specification and User's Manual for the Z16C30. The User's Manual covers the serial protocols supported by the Z16C30.To access the Z16C30 User's Manual (. See similar questions...

You can connect up to 15 devices to one RTU, in any combination of digital or analogue. This can also be expanded using the low-power Radio Frequency (RF) network option available. See similar questions...

Ans: Cable is the primary medium for transferring data between 1394a devices To support the maximum 400 Mbps transfer rate, the cable can be no longer than 4.5 meters. For 200 Mbps transfer rate, the distance can be extended to 14 meters. See similar questions...

We recommend using distances up to 200 meters. Under ideal conditions it is possible to reach longer distances. This depends on the type of cable and the quality of the joints. Diagnostics Kit will help you find out the maximal distance between the most distant outlets, so that you still reach sufficient throughput. See similar questions...

This depends, of course, much on your organization, for example on its size, the type of development and how advanced your processes are already. As a rule of thumb if you want to be successful, you should not be afraid to spend 5% of the software development effort or more on SPI. 5% or more sounds like a lot, but you should know, that many companies that spent that amount could report a formidable return-on-investment later. See similar questions...

mm/sec (42 inch/sec). When engraving an A4 (18 x 28 cm) size square with 250dpi at full speed, it takes LaserPro 18 minutes to complete. See similar questions...

The maximum sewing speed on caps is 1200 SPM. To achieve good results at this speed all adjustments, such as hooping, material thickness, and the design itself need to be correct. When sewing on structured caps with a heavy buckram inside, use of a Titanium or Teflon coated sharp needle is recommended. This reduces friction, which will reduce thread breaks caused by heat at higher speeds. Refer to the AMAYA Operator's Manual, for more suggestions and instructions regarding cap sewing. See similar questions...