These locks will fit some storm doors and not others. If the storm door has a handle that is like a typical non-storm door with a regular lockset then these locks will work. However, if the storm door has a light weight aluminum handle latch these will not work.

Ensure you read the section under the blue button called "Backet/Sizing" located in the lower right corner of the website. You can also download a template there for helping you determine the backset of the locks already installed on your door.

No, EVERBRITE? will not damage or compromise metal hardware or locks. In fact, EVERBRITE? will protect the locks and hardware from rust and corrosion as well.

Is there a build-up of ice or snow under the door? The door may be frozen to the ground. Remove any restrictions. Repeated operation may have tripped the overload protector in the motor. Wait 15 minutes and try again. Is the door control lit? If not, remove the bell wire from the motor unit terminals. Short the red and white terminals by touching terminals at the same time with a piece of wire.

There are none?Kin the car that is. Yes, the ??Power door locks?? are simply the door knobs themselves?Kpush down on the driver??s side to lock both doors, pull up to unlock both. Or, you can use the key??s remote to lock/unlock the doors. On an interesting note, if you are leaving the car and want to lock the doors, you cannot push the knobs down while the door is open?Kyou need to close the door and use either the key itself or the remote transmitter??s lock button.

Yes, spare parts are available for all door locks. Please call our freephone helpline 0800 393 405 for details and pricing.

Open the door and check the metal plate on the edge, it will usually be engraved with the name and type of lock, and if applicable, the British Standard kite mark.

The central locks usually bounce or ratchet when they are not properly centered. One or both of the actuators in the front doors need to be centered more accurately with the linkage. In other words, assume the actuator has a travel of about 7/8 inch and the door lock linkage moves 1/2 inch (just a guess). Moving the actuator 7/16 inch brings it to the center of it's travel and moving the linkage 1/4 inch brings it to it's center.

The BIX-02 model is a simple lock to fit on most doors. It is an ideal replacement for most knob locks. The lock comes with a template and instructions on DIY installation! We recommend you contact a locksmith to fit the BIX-03 model. A list of recommended locksmiths can be provided on request

All retractable screen doors are custom built to 1/16 of an inch, for your home and your home only. The screen can be installed on practically any opening, measuring up to 120" in height and 140” in width.

When installing our deadbolts you want to make sure that your door is somewhere in between 1-3/4in and 2-1/4in in thickness. If your door is not in that range please call customer service. When installing our standard doorsets you want to make sure that your door is somewhere between 1-3/8in and 1-3/4in Note that extended spindles are required on passage locks that will be used on thicker exterior doors. These are offered by special request only.

Measure Out-swing storm door or In-swing core door, (measure just the swing door). Add two inches to the width and one inch to the height, then round up to the next inch. (Example: Out-swing storm door measures 31.5 inches wide by 74.5 inches tall, you need a 34" x 76" call size.)

This all depends on the type of Door Lock System that is installed on your vehicle. There are (3) Three basic types; Type "A" Positive, Type "B" Negative and Type "C" Reverse Polarity. If your vehicle has a Type "C" Reverse Polarity Door Locking System and your Pro-Series unit does NOT have On-Board Door Lock Relays (5-Pin Door Lock Harness), you will need the extra relays Part 778.

The Charleston has a standard Kwikset keyway; if your door also has a Kwikset keyway, most locksmiths can key the two locks the same. If your other doors use a Schlage keyway, you can buy a Schlage keyway for the Charleston that can later be modified by a locksmith to be keyed-alike.

The smaller models may fit but the larger models are unlikely to.See the dimensions for the models. We generally transport the Spas on the side with the use of a Spa trolley

Our door opener can be fitted to some UPVC doors depending on locking system. A site survey is recommended for this type of door.

Just measure the distance between the centres of the two holes on your existing door-knocker and make sure that you check the General Details page to ensure that the bolts line up. That’s it

Check the details of the fixing hole positions and the key-hole if relevant. The details are shown on the general details page for each handle.

First, visit our Hardware Replacement Page to determine which type of hardware is the best mechanical replacement of your current hardware. Once you’ve found the replacement lockset that’s right for you, you’ll then want to check trim plate dimensions. On each product feature page, you’ll find a link called Trim Plate Dimensions. Clicking on this link will open a PDF file with a outline of the trim plate(s) for the particular hardware you’re considering.