HOTSPOTZZ requires only a few simple changes to your computer. Use this table to locate instructions for your operating system and wireless LAN card. If you don't see your card or operating system here, write to our customer service team or call 1-866-776-8991. Customer Service hours are Monday - Friday 9 am to 6 pm MST.

Yes, the Connect-A-Dock can be reconfigured, added to, and moved to another location. The unique connection system is very flexible, and you can reconfigure the same components into many different shapes. (i.e. T, F, L, swim platform, etc.) Different configurations may require additional float sections and/or connectors. These can be added at any time. See similar questions...

The following procedure readies a Falcon for use with a custom UPG program, IntelliTrack portable application, or standard PAL software. Reconfiguration should be done whenever there it is suspected that the loaded configuration or application files have become corrupt or a malfunction occurs. Usually, this is evidenced by erratic performance. See similar questions...

You might have to change the CCFLAGS field from '-I/usr/local/ssl/include/openssl' to point to wherever your openssl .h's are. Also, you might need to add to LIBS the location of your openSSL libraries if they are not in the default location. See similar questions...

To reconfigure the NVRAM, you first erase the Cisco 675 or 678 modem configuration and then reset the modem. See similar questions...

Make sure your scanner is plugged into the correct interface. Then turn to the front cover of your configuration manual and scan the following marked bar codes: "start", "set", "end". This sets the scanner back to the factory setting and keyboard wedge interface. If there are changes you need to make, such as setting the data start/end characters or using RS-232 (serial), scan those codes before scanning the "end" code. See similar questions...

Any settings that you can change can be found by clicking "MY ACCOUNT" at the upper left hand corner of the page after you log in or by clicking here. See similar questions...

I would not be able to give exact values as there are many differences even between identical setups. Besides it is best to do the setups individually to give the most optimal settings. I can however give some pitch setting to go with for learning to hover. I have setup a lot of helicopters and for those just starting out I always setup 0 degrees blade pitch for bottom stick position, 5 degrees for the middle stick position, and 9 degrees for the top. See similar questions...

There is no need to change computers using private addressing. If you have a router involved in the configuration, you may have to change the IP address of either the router or the Smart IAD device in order to allow the Smart IAD to pass the voice traffic. See similar questions...

If all the ME users have analog phones on their desks, then it is unnecessary to do anything with the PBX. If not, it is necessary to modify the PBX configuration. See similar questions...

Not usually. There is typically no need to configure your network or firewall. You can install it on any PC connected to the wireless network running Microsoft Windows 2000, XP or Vista. Yes - myWIFIzone now supports wireless networks running WEP. In fact, if someone hacks your WEP key, they will still be blocked by myWIFIzone. See similar questions...

You can reconfigure those CPLDs but we don't recommend that you do so. The factory configuration for those CPLDs is designed to use all the pins on those devices and it is highly unlikely that you can develop a design capable of driving all of the devices on the I/O board you are using. You may be able to develop an LCD driver that could work but other devices on the I/O board would no longer work. See similar questions...

make reconfigure only works within the core Harvest code (the files in the src/ subdirectory) and not on any of the components. This is a bug, which will be fixed. However, a similar result can be obtained by using 'make realclean', on the next 'make' the software will be reconfigured. This section contains questions about, and solutions to, some of the problems that have been encountered when running Harvest. See similar questions...

Settings option allows you to edit your personal information. You can change your Reymount login password, personal password, idle time settings, and equity stop-loss point. See similar questions...

You will need to reconnect the stator leads and regulator. For generators other than 12-wire KAMAG generators, please contact the Kato factory. Please have your serial number ready. See similar questions...

AdvantAir is completely transparent to the applications already running on your computer, you do not need to reconfigure anything. See similar questions...

If you have been using a modem/router with your ADSL service, which is already ADSL2+ compatible, you will not need to reconfigure it. If you have purchased an ADSL2+ compatible modem/router from TPG upon registration, you just need to ensure your modem/router holds your current password. If you require assistance with this, please contact the TPG Technical Support on 1300 360 855. See similar questions...

Yes, you can push new configuration settings and content filters to active clients on your network from your central location using the viewer's "Synchronize Settings" function. See similar questions...

To change your newsletter and reminder option, just log into your account at MyStart! Online, and click on Edit Profile in the top right hand corner of the screen. There you can change all your options for weekly and monthly e-mails. See similar questions...