No. Range hoods are specifically designed to handle grease and high temperature environments. Ventilation provided by NuTone fans is only a supplement for odor and moisture removal in the kitchen.

The wall jib must be mounted to a structure determined by a qualified person to be adequate. The thrust and pull forces given for each jib, the weight of the jib, the capacity, impact, and hoist weight are some of the factors that must be taken into consideration.

Smaller ceiling fans (up to 110 cfm) should not be installed in the wall due to mechanical concerns (motor orientation, bearing lubrication, built-in damper, etc.). However, if they are installed in the wall, the duct needs to be pointed up to allow the damper to operate, but the bearings may not last as long as specified, due to insufficient oil flow within the sleeve bearings. Larger fans (190 and 340 cfm) can be installed in either the ceiling or wall.

If you have a single wall switch with two wires, you cannot unless you buy a control designed for this kind of switch. An electrician will have to run a third wire to the single wall switch and you must purchase a dual control to operate the fan and light from the single switch. An alternative is to purchase a wireless remote control that can operate both the fan and light so you will not have to do any electrical work.

A3: Horizontal distance between ceiling fan blade tip & nearest wall should be 0.5times the fan size.

Panasonic has a new wall fan, the WhisperWallTM, that is currently going through Underwriters Laboratories testing. This will be the choice for wall applications when it becomes available in the market. The smaller ceiling fans up to 110 cfm generally should not be used in the wall due to concerns about orientation of the motor for bearing lubrication and the built-in damper on the discharge side of the fan.

A2: Minimum distance between ceiling or a projecting beam & ceiling fan blades should be 0.25 Mtrs ( Approx 9.5 Inches )

Generally it is not recommended to use CFLs in vibrating environments. Vibration can cause the electronics in the CFL to fail. There is one CFL bulb (FLE11) that is available for use in a ceiling fan. Check the package for this application.

You can use a ceiling fan anywhere you have a ceiling. Covered decks, porches and gazebos make great spots for a fan. Underwriter's Laboratory lists fans for outdoor use are two types of listings: "damp location" and "wet location". Damp location is suitable for most outdoor uses while wet location is intended for more severe situations.

Yes. NuTone bath fans are designed to provide adequate cooling for motors and lighting, as well as products with integral heaters.

Definitely. Joyce? provides a fan beam mullion for the studio rooms to conceal the wiring. For a gable room it is mounted to the ridge beam. You should make sure you have the proper clearance.

Yes. Most manufacturers of ceiling fans have adaptable fan canopies or mounting systems that enable installation on high ceilings. Follow the instructions provided with your fan for details. If your fan does not have such items included, most ceiling fan retail outlets carry accessory adapters that can be used for this kind of installation.

This depends mainly on the CFM (cubic feet per minute) rating which indicates the amount of air flow that is moved. Your ceiling fan dealer or manufacture can determine the CFM ratings for different ceiling fans. Another way is to compare different fans during actual use in the store and feel the breeze each produces. The fan with the greatest breeze will usually have the greatest CFM rating.

A wireless remote can be attached to most ceiling fans allowing remote control of the motor and light.

A8: Efficiency of a ceiling fan is a ratio of air delivered by fan in Cubic Mtrs Per Minute and electrical power input in Watts, when fan is operated at rated voltage. (This is also known as a ?service value? of a fan ).

We don't need to remove them. When the room is dark, the lamp will not be noticed or get in the way of the stars. Same with ceiling fans. They are not an obstacle. In fact, when the fan is on, it feels like a breeze coming down from the sky.

Blade pitch is the angle of the blades when compared to the horizontal. Quality fans generally have a blade pitch of 12-14 degrees. Lesser fans can have a blade pitch as low as 8 or 10 degrees. The higher the pitch, the more pressure the fan blade applies to the air in front of it as it turns and the more air is forced downward. That's why some lesser quality fans can look like they're spinning up a storm, but when you stand under them, you can't feel anything.

The DeGeorge Fan is the only one of its kind in the world. Our fan is unique because of its safety factor which is absent in all other ceiling fans. Great for confined or low-ceiling areas. The fan features two motors: the first motor rotates the six 45-degree pitched blades, and the second rotates the bottom louvered grill.

The electrical fan has it own shroud on which the mounting feet are attached. Tie rods are used to mount the fan directly onto the radiator core.

If you mount a fan on the front of a radiator it will suck cool air, but then the air hits the radiator core & try's to bounce back. With the fan on the back of the radiator the air is sucked through the core, the resistance the core offers loads the fan but no cavitation occurs because the air is then dumped to atmosphere.