There are many factors that can cause a printer to print slowly from an Operating System, Application. However, there is a small setting in the Lipi Windows 95/98 drivers that may improve the printer's performance. The Lipi Drivers have a default printing matrix set to 360 x 360 dpi (dot per inch) resolution. This resolution value can be reduced easily to 180 x 180 without creating print quality reductions. This 180 x180 resolution will increase the printing speed of each character.

It's very useful because it means that if you set two series connected filters at the same frequency (filters # 1 and 3 or 2 and 4) the boost or cut value of each filter sums. Simply stated you get up to plus or minus 24 dB of adjustment through the use of a pair of filters.

Although similar in intent the collectors are different in some details of the implementation that make the parallel garbage collector better for some applications while the parallel young generation collector is better for others. Both should be tried to determine which might be better suited to a specific application.

NT4 does not have usb support, and we recommend our users to use either Win 98 or Win 2000. We can offer support for NT4 only for large customers under special conditions for our devices- including usb to serial or parallel.

TEAMNisca recommends the Belkin Pro Series IEEE 1284 Printer Cable (A/C) - 6 feet, Belkin Part Number: F2A045-06. This cable offers a Nisca compatible male DB25 to male Micro Centronics 36 Pins connectors.

The V.24 serial interface is quite simply best suited for this application. Its connection cable can be extended to almost any length and does not produce long-wave interference. USB has a maximum cable length of 8 metres and high interference levels. The same goes for other interface types. This is simply not true. See previous question. There may be radio clocks for which this applies; for the NeoClock it is not true. This is also not true.

Answer: Yes! We have the serial interfaces for several Okidata dot matrix and laser printers. To find it, scroll to the bottom of the dot matrix page under the title of "Accessories and Options for Dot Matrix Printers". Serial interfaces are available for the ML184, ML320, ML320T, ML321, ML321T, ML390T, ML391T, ML420, ML421, ML490, ML491, ML520, ML521, ML590, and ML591. The PM 3410 and PM 4410 come standard with both serial and parallel interfaces.

Generally, the deciding factor to this dilemma is the total speaker load impedance you wish to drive. With Micro-Tech and Macro-Tech amplifiers you would want to use Bridge Mono to get the most power available when driving 8 or 4-ohm loads (one or two 8 ohm speakers). With a Power-Tech or Com-Tech amplifier you need to stay at 8 ohms or greater. Parallel Mono can be used when driving lower impedance loads. A one-ohm load can be driven Parallel Mono with a Micro-Tech or Macro-Tech.

The printer should print the directory listing in 40-column mode. To check the lines, do a regular directory listing:

With rev 3.0.25. Configure the parallel port as Centronix port in the bios, then UR30 handles pins 1, 10, 11, 12, 13, 14, 15, 16 and 17. Parallel port pins 2 to 9 are always handled as output pins (eg : external lane power supply control or external light control).

If the only problem is that the printer is terribly slow, try changing your printer po rt mode as discussed in the Printer Setup section of the Handbook.

Yes it is. You can send simple commands from a remote device which duplicate the MODE and ZERO key functions. You can also request the balance to transmit the weight. If the pan is empty or near empty when the power is restored, the balance will re-establish and display zero. If the pan is loaded the balance will display all dashes. You then may remove the load and establish zero or press MODE to continue weighing.

If you're using a modern PC running Windows XP or Vista, then you should probably get a USB interface. Although USB interfaces are no faster than serial versions, it's becoming increasingly difficult to find new PC's with serial ports, so a USB interface is more future-proof. If you're using a PC running an older version of Windows or with a CPU speed of less than 1GHz, we recommend a Serial interface.

Your software will support more than the standard four (COM1-COM4) COM ports available to the machine You have enough available slots in the machine (up to eight slots). The following outlines Quatech support provided for different operating systems. Windows 95/98/Me/2000/XP is able to support many more than four ports at one time. Quatech's driver must be used in order to access ports above COM 4. OS/2 also should have no problem accessing the cards up to COM32.

Answer: No. The License Tool is only used to upgrade one serial number at a time. You can go through the process for each license you need to upgrade or contact Bentley Sales Support.

lines to your /etc/initab file: # this will initialize the modem port on startup md:b:once:i:/usr/sbin/runover .ttya /bin/stty 38400 You should of course change "38400" to whatever speed is appropriate for your site.

Answer: Yes! We have a serial cable that will work on most serial dot matrix and laser printers. It is a DB9 to DB25 null modem cable. If the communications port on your computer has a DB25 connector, you will also need the 9 to 25 adapter for this cable. We can also provide a DB25 to RJ45 serial adapter if necessary. To find these items, place the word "cable" in the search window (located at the top left side of each web page).

Take a quick trip to the How To Buy section of this Web site for all the details. If you still have questions, please feel free to Contact Us.

Whenever using the serial or parallel port, you should always use the AC adapter. These ports require about as much power as the Portfolio and will quickly drain the batteries.