In a word, no. Unless your data modem has specific additional support for fax, you cannot communicate with fax devices using a data (only) modem. Simply put, the problem is that the modulation methods (tones) used to communicate data are different from those used to communicate faxes. Typically the modulation schemes used for fax are synchronous half-duplex while those used for data (at least by most UNIX and PC people) are asynchronous and full-duplex.

Unfortunately, that's far too complicated a question to answer here. In general, turn compression off, and turn uucp 'spoofing' on. This can all be done on the fly by sending register settings as part of your send-expect sequence when you call out, or you can do so as part of your modem initialization string in static. Some Telebit modems don't save the register settings. You might have to set the registers in both the init string and in the calling sequence. See similar questions...

Motorola SURFboard cable modems use some of the latest data encryption technology to help minimize security risks for your data. However, a little extra caution never hurts. We recommend you turn off your file- and print-sharing options when you're not using them and carefully review any other security precautions your service provider might recommend. Also, the Motorola SURFboard cable modem provides a top-mounted standby button for enhanced security. See similar questions...

No. Your Reliance IndiaMobile has a built in modem and is configured to communicate to the Reliance CDMA 1X network only. See similar questions...

Yes. Just enter the IP address of the CDPD modem and port 12345 into the iCGRS Eth Setup page and start to stream DBN and SVN in binary at 1 per second. The CDPD modem will receive the data and transfer it to the rover receiver through its serial port. The power supply we provide puts out 24 VDC. The receiver will draw its power from the highest voltage source. See similar questions...

Faximum makes it possible for a single modem and phone line to handle fax, data, and uucp traffic. This feature is, however, only available with certain modems and systems. Contact Faximum Software for details. See similar questions...

Using a modem is no problem. The keylogger will silently check if you are connected to the Internet. It will not start dialing. Thus, emails are only sent when the modem is already connected to the Internet. See similar questions...

The SURFboard cable modem will not enter standby while the "Receive", "Send", or "Online" LEDs are flashing. The flashing of any of these LEDs indicates that the cable modem is in the boot process. Once this process has finished, you will be able to press the standby button and place the modem in the standby mode. See similar questions...

If you wish to only provide data (of the hosts that your DenyHosts daemon has blocked) to the denyhosts.net server but not receive hosts that have been denied by others you can set your SYNC_DOWNLOAD to no. The default is yes but only applies if synchronization mode has been enabled. See similar questions...

Yes, all transmissions will be encrypted en route so as to avoid any interceptions. This service is provided by HUD's Secure Connection System. See similar questions...

You may use any you'd like. Please note: it is your responsibility to purchase the correct, DSL appropriate, modem. If you need assistance, please contact our customer support team. See similar questions...

No, Alpha Telecom has a list of approved modems that have been tested with the ADSL service and are ACA approved. You may install a non Alpha Telecom if it is approved. Most importantly, it is a legal requirement that any equipment connected to the ADSL Service must be labelled with the ACA telecommunications compliance mark. See similar questions...

No. J323 Engine is an implementation of the H.323 Version 2 protocol as defined by the ITU-T (International Telecommunication Union). The H.323 protocol is a Voice-over-IP protocol. It is used to establish phone calls over an IP network (such as the Internet). Therefore, J323 Engine will communicate only with H.323 endpoints. A H. See similar questions...

Many settings can be executed through so-called AT or modem commands. Permanent settings should be entered directly in the parameter line. For short-term settings this method isn´t practical. It is better to send the commands through a terminal program to the cFos virtual modem instead. Launch a program called Hyperterminal, which can be found under [Start] → "Programs" → "Accessories" → "Communication. See similar questions...

What are the new digital phone networks capabilities for data communications? [ie. Can I use my One2One/Orange phone?] See similar questions...

ClearSail recommends that no modems be used under the speed of 56K. It is recommended that you consider upgrading to a 56K x2 or v.90 modem. These modems will perform approximately twice the speed as a 28.8, and with prices coming down, most major computer stores offer 56K v.90 modems for under $50.00. See similar questions...

A#8.6: Currently the GNO serial drivers only support the two built-in serial ports. This does not imply that you cannot use a serial card in a remote machine (such as a IIe) that is connecting to your IIgs running GNO. A#8.7: These settings will usually work. See the Notes, below. See similar questions...

Yes, of course. You can simply send encrypted files generated by Cryptainer LE over email. Use any email client like Outlook Express or Netscape mail or any web based email service like Hotmail. The recipient need not even have a copy of Cryptainer LE to view these encrypted files. See similar questions...