When the thermostat is set to "auto," the fan operates only when the temperature requires it. This is the most used setting. When the thermostat is set to the "on" position, the fan runs constantly. There are advantages to using the "on" setting. First of all, the air in the house is constantly filtered through the unit's air filter. Secondly, the constantly circulating air may result in a more even temperature throughout the house.

This depends ont he type of furnace you have. If you have a furnace equipped with D.C. (E.C.M) variable speed motor, then yes. This is one benefit of the variable speed motor: you can affordably operate your blower 24 hours a day because it circulates the air in between demand cycles at a lower rate, and uses a lot less energy than a conventional blower motor. If, however, you have a furnace equipped with a conventional motor, you should operate the fan in Auto mode. See similar questions...

There are advantages. One is full-time filtering of the air in your home. Another is that you can maintain a more even temperature throughout your home. See similar questions...

We normally like to set thermostats at 90 to 95 degrees. It's a lot cheaper to run your attic fans than your air conditioner. See similar questions...

The recommended setting is 60 – 75 °C when with domestic hot water production and 50 –55 °C without. Do not set below these settings, as condensation may form within the main body that with time, may damage the exchanger. See similar questions...

months. One is that you get constant filtering of the air in your home. The other is that because the air is moving, you have a more even temperature throughout. See similar questions...

Running the fan all of the time will increase the amount of filtration and will tend to even the temperatures throughout the house. However, a constant fan operation can also raise the humidity in the house during the cooling season unless a separate dehumidifier is used. It is normally advisable to run the fan continuously in the winter but not in the summer unless some sort of additional dehumidification is used. See similar questions...

Auto-Pay is a convenient way to pay your rent automatically by having our system debit your designated account for the exact amount of your rent every month on a pre-specified day. As with all transactions that you make on Tenantplus.com, your manager will receive instant notification that you have paid your rent. Auto-Pay will also send you a reminder in advance before your account is debited. You must be registered and have an active Tenant account with us to pay your rent using our system. See similar questions...

For this type of application, the Aube TH140-28-01 must be used since it can operate on 120 or 240 volts. See similar questions...

Generally, you should set your thermostat where you feel comfortable. But we recommend keeping your thermostat at 73-degress or higher in the summer. Lowering your thermostat below 73 can cause your indoor coil to freeze up, leaving you stuck without any AC until it thaws! See similar questions...

In the AUTO shooting mode, the camera operates with a minimum of input from the user. Many shooting functions are controlled entirely by the camera; the photographer cannot change their settings. Therefore, the menu options that control those settings are deactivated (grayed-out) in AUTO mode. See similar questions...

Try both ways. Running the blower all the time will use a little extra electricity, however the home is usually more comfortable, the temperature is more even throughout the home, and the air is cleaner because it is filtered more. The motors generally last longer because they are not starting and stopping. Some of the new furnaces have the ability to use a slow blower speed for continuous operation, and a faster speed when the furnace or air conditioner are running. See similar questions...

First, open the Soloist HMI, save your program as a .ab file, and use the Build button to build an executable .bcx file from it. Then, connect to the drive you want to auto-run the program on and open the File Transfer Screen. Send the executable .bcx file that was just created (it will have the same name as the .ab file, but with a .bcx extension) to the drive. Then once the file is listed in the file list right click and selecte Set to Autorun. See similar questions...

Answer: Yes. We encourage you to set your domain to auto-renew to avoid losing your domain or having your Web site go down when the domain expires. See similar questions...