Each stove's installation requirements are different. Every manufacturer tests and lists each model. Clearances to combustible walls and hearth (underlayment) dimensions are critical safety considerations. Local building officials will rely on these specifications when inspecting an installation. Every stove's requirements are included in the owner's manual and in less detail on the identification plate on the back of each stove.

General contractors or any firm hiring for the purposes of construction, transportation or logging should get clearance information on their subcontractors before work commences and before any payment is made. See similar questions...

I've never had to do it, no I don't know much about the subject, so I'll point you to a FAQ on the subject. See similar questions...

That depends on how old it is and how you use your stove. While modern, EPA certified woodstoves are extremely efficient and emit very little particulates into the atmosphere, older uncertified woodstoves (pre 1991) are inefficient and emit an excessive amount of particulate matter. The Heat Green Council encourages consumers to change out their uncertified woodstove with a certified one and to practice smart burning methods, like using only properly dried wood and never burning garbage. See similar questions...

The Fire Department does not inspect woodstoves. New installations of woodstoves require a permit from the Building Department, 150 East Main Street, Suite 250, call 503-681-6145. Existing installations should have proof of a permit or written approval from the Building Department. (Return to Top) See similar questions...

Your woodstove was built and designed to burn at top efficiency using the size exhaust that is has. Reducing the exhaust size will most certainly cause the woodstove smoke every time you open the doors to add wood. There are a few exceptions to this rule and the height of the chimney is the main one. The higher the chimney, the better the draft. So if you have a chimney that is around 30' tall or taller, you probably can downsize. Refer to the manufacturer of your stove for advise. See similar questions...

The basic clearances required to acquire a property are: a. A no objection certificate (NOC) from the society where the property is located however if a property is purchased from a builder no such NOC is required. b. The income tax department 37 (I) clearance is required if the property is above the value prescribed by the appropriate authority constituted under Income Tax Act, which value is Rs 75 lacs in Mumbai city. See similar questions...

No! Each county school district has their own security clearance requirements and there is no reciprocity amongst the counties. See similar questions...

The most important area of concern is the maximum safe distance between the IR window and any live components; this is called the “dielectric clearance”. The recommended minimum dielectric clearances are as follows: See similar questions...

a guide, clearance across the width of the footway should be one metre back behind the column, or to the boundary of your property whichever is the shorter. Where the column is located in a grass service strip, the boundary of your property should be taken as two metres back from the road. Foliage should also be cleared to a one-metre radius around and above the lantern. See similar questions...

Absolutely no State Government clearance for a software unit. From the Government of India, you may need foreign investment clearance from the Foreign Investment Promotion Board. You may also need STP (Software Technology Park) registration, if you are planning a 100% Export Oriented Unit (EOU). Both these can be organized easily. A 100% export oriented unit (EOU) need not pay any duty. Imports are duty free. Otherwise duty depends on the items imported, and will be about 35%. See similar questions...

If I have to spend time putting the basics right, that means less time testing. I’ve had people arrive with engines in such a poor state that in some cases I’ve had to spend several hours working to correct the faults. In most instances these faults could have been addressed by the owner. I’m quite prepared to do this kind of work but it means you’re paying for time that could have been spent more productively testing the engine. See similar questions...

Every applicant over the age of 18 must obtain and submit a police clearance certificate from each country they have resided in for longer than 6 months since turning 18 years of age. These clearances must be obtained by you and must be original documents submitted to us. See similar questions...

If you need a bigger than available shim, that means that your valve does not stick up above the head far enough. Probably the easiest thing to do is take the head off and take it to a good machine shop that does valve work and have them dress the seat of the offending valve. Taking material off the seat will make the valve stick further though the head, necessitating a smaller shim. Cost you a head gasket and about a half hour of a machinist's time. See similar questions...

Typically clearances decrease due to valve seat/face recession. this is erosion cause by high head, metal transfer, etc. once a valve clearance tightens up to zero, it stops transferring heat across this boundary (cause the valve never really touches the head/seat when "closed") and erodes much faster. Clearances increase due to a number of issues, one obvious one is if you bend a valve, and it can no longer fully close. Intakes don't usually bend, it's the exhausts. See similar questions...

The system uses on-screen pop-up menus for input of instructions and clearances to aircraft. It uses exactly the kind of HMI techniques that will come into operation in real ATC systems in the not-too-distant future. (Currently there are very few truly electronic ATC systems. Most still use paper strips, and even those without strips still make very little use of electronic support. See similar questions...

For overhead doors you need 18" additional height for door track and 3" on each side for the side door track. What are you putting in the building? If your boat and trailer have a combined height of 10 feet, you need to plan on a building with 12 foot doors See similar questions...

Typical installation takes less than an hour. Only two wires need to be connected and routed. Mounting on the instrument panel is accomplished with a Velcro? hook and loop fastener. Routing of the two wires must consider possible sources of abrasion. Good aircraft electrical wiring practices must be followed. See similar questions...