Yes if you specify this at time of ordering our installers will provide you with a suitable USB to Ethernet converter at time of installation

Connecting the digitizer with Serial (RS232) or USB will be determined by the application software you are using with the digitizer. Please consult your application support for assistance.

If you are connecting directly to one PC, under windows 98SE, 2000 or XP, either Parallel or USB is usually fine. However, the way XP handles USB devices may cause you to lose the device occasionally. This is because XP assigns virtual USB ports to multiple devices on the same USB bus. If the plotter is switched off or disconnected when the PC is booted up, it may be found later as a new device on a different virtual port, and the driver may need to be installed again.

Yes. A separate, Keyspan brand USB adapter can be purchased for your board. The adapter attaches to the end of the serial cable provided and then connects to your computer. The USB adapter can be purchased through GTCO or your local reseller.

With the current adapters you cant, the USB modem is the DSL equivalent of a WinModem and requires some processor power to perform the modem functions and convert the ATM data into TCP/IP for presentation to the PC. There is a Draytek device however which can effetively act as a router and presents ethernet to the user side. See details here.

The EVOLT E-500 is USB Auto-Connect (mass storage) and is compliant with USB 2.0 Full-Speed specifications.

No, Penn State Access Accounts are intended for use by a single individual. If you find that your Ethernet connection is disable contact ResCom. A. Can I set up a wireless connection in the Residence Halls? No, as stated in AD20, "Respecting the physical hardware and network configuration of University-owned networks. System users must not extend the physical network on which their system resides (e.g., wiring, jacks, wireless connection)".

Either type of connection will work if you have the correct port available on your PC. If you have Ethernet ports available these are often the best choice as they do not require software installation to function. USB is the other popular option and provides good connectivity after you install the adapter's driver software. Examples: Linksys Wireless USB adapter for Desktop or Netgear Wireless USB adapter

Ethernet is easy to install and will generally give you better results. You must have a computer that supports Ethernet or has an Ethernet card (sometimes called a "NIC", or Network Interface Card) installed. USB will work on most computers that have been built since 1998 and is a good choice if you know that your computer does not have an Ethernet connector.

Some DSL modems carry USB capability. This is useful alternative in instances where a network card cannot be installed. Please note that you cannot use the USB port of a usb HUB to extend the wire length between your modem and PC, or share the access to multiple systems. You can use the USB and Ethernet ports at the same time to facilitate access on two machines provided the advanced modem routing features are enabled.

Using a USB connection is actually no different than a network adapter card on the WinGate server; the configurations will still apply from the WinGate helpdesk based on the operating system you are using. The USB connection will show up in the network properties and will be available for configuration.

Absolutely nothing at the moment. All three are disabled. Some people have reported that USB keyboards work, but it's not a supported feature. Others have also powered a PC cooling fan off the USB, but that really isn't necessary. Just keep it well ventilated and it'll be fine.

Yes. The i.LON 10 Ethernet Adapter (version 2.x and higher, available from April 2004) supports an external modem attached to its serial port. When used with an external modem, the i.LON 10 Ethernet Adapter uses PPP as the serial protocol. The i.LON 10 Ethernet Adapter version 1.x does not support PPP.

Yes but you must register FreePOS first in order to do so. The unregistered edition of FreePOS only works with Parallel (LPT) printers.

How do I get the "Flexible Content Aggregation" sample to work? I get an "Connection timed out" exception.

Ethernet looks like a typical phone jack. Most computers built within the last 5 years will have an Ethernet card already installed. It provides a link between our service and your computer via an inconspicuous wall outlet.

You can use either a USB data cable connection OR a Bluetooth connection in order to sync your phone. Bluetooth technology provides an added benefit of allowing you to sync your phone while it's still in your pocket, but you can just as easily connect your phone using a USB data cable. The choice is yours!