It's never a bad idea. Lowering your car changes the car's center of gravity. Stock plates may not be able to account for the extra degrees of caster and camber that will be needed when getting an alignment.

Each vehicle will require different specifications so it is impossible to give one set of numbers that will work for all vehicles. However, we recommend starting with the factory specifications and fine-tuning from there. Remember, due to the portal design, relatively low caster numbers are ideal. See similar questions...

Here is a great site that I ran across that explains all of the above with pictures: http://www.advancedracing.com/grmart1.html. See similar questions...

Camber plates sit at the top of the strut, and allow the strut to be adjusted in several directions. Changing the attitude of the wheels. You will also see the term pillowball mounts used when discussing camber plates. See similar questions...

Positive Camber = Tops of tires point outward. If you look at the front of the car you'd see: V FRONTAL VIEW __ ( ) W ( ) __ Tire \ \ ---------- / / Tire -- -- Negative Camber = Tops of tires point inward. Too much negative camber ==> Tires wear on the INside more than the outside. Camber affects directional stability and tire wear. A difference between the front wheel camber settings will cause your car to pull to one side. See similar questions...

A: When lowering your vehicle a camber kit is HIGHLY Recommended for tire longivity and power alignment/camber. See similar questions...

Yes. Lowering your car changes your alignment specifications. At a minimum, you will need to have the front toe specification reset. For cars that spend a lot of time traveling in a straight line, a very small amount of toe-in (1/16" to 1/32") will help keep the car tracking straight. For performance driving, a slight amount of toe-out (1/16") will help your car turn into corners faster. Your car may also need to have the camber and caster specifications checked and adjusted. See similar questions...

Camber gains (-negative ) can be gained on these cars with these methods- The factory recommends slotting the lower strut hole /to knuckle/ to the outside, and you can then pull the bottom of the knuckle out farther to gain more negative camber.You can also slot the upper hole to the inside, but the knuckle contacts the strut housing when you move it in at the top and may also cause a tire clearance problem to the upper strut area if you are using larger wheels and tires. See similar questions...

It's your choice. If you've purchased a new vehicle, you can either receive new plates or pay a $15 registration transfer fee to use your old license plates. See similar questions...

Failure to meet Camber requirements leads to the intensity of modulation sidebands, particularly harmful at higher fields, where optimum sensitivity and resolution are required. When Camber becomes excessive, sample tubes can make contact with the inner surfaces of the probe causing time consuming and expensive repairs to the probe. See similar questions...

Lowering your car changes the camber, which in turn changes the toe settings. Both will cause increased tire wear, so you should have them adjusted to account for this. See similar questions...

In general, it is safe to lower an Isuzu car 2 to 2 1/4 inches without having to worry about clearance problems between the tire and the structure in wheel well of the car, as long as the spring rate is raised enough to counter bottoming of the suspension and as long as the correct wheel and tire size is used with no wider than a 7 inch wheel and no wider than a 205 series tire depending on the model of car. See similar questions...

Camber is a "crown" purposely built into a glulam at the time of manufacture. It is most often desired in long span applications to counteract deflection. Camber does not affect the strength of the beam. Residential stock beams are normally made in either 3500' radius or zero camber, while other engineered wood products are zero camber. See similar questions...

Some ways might include: shopping for another auto insurance company, asking for discounts to stay on or purchasing additional policies with the insurance company. Another practical way to save money is to raise your deductible and risk paying more in a minor collision in hopes of lowering your yearly premium costs. This is a gamble, but if you're a good defensive driver it might be worth considering. See similar questions...

In short, you need to make sure you have all of your documentation in order including the sales contract and proof of the purchase price. You will register your new vehicle through your local tag agent. See similar questions...

If you are buying the car from a dealership, they may offer a service to register and title the vehicle for you. The dealer must provide you with the MSO (Manufactuturers' Statement of Origin),... | more See similar questions...

Auto license plates can be renewed the month before, the month of, or the month following expiration. Iowa DOT Web Page The driver's license station is located at 501North Carroll Street in Carroll and is open Tuesday - Friday 8:30 am - 5:00 pm. and 8:00 am - 1:00 pm on Saturday (Holiday Schedule) Visit the Iowa Drivers License page for more information. See similar questions...

a) Car Tags plates are a low cost, "buy it once, and use it for years" product, which delivers dividends every day. b) A Car Tags plate affixed to the family car becomes a personal endorsement passively promoting your product. c) Their mobile nature means they are seen by a different audience every day. They sell whether you are on the road or parked, at work or play. See similar questions...

No. Absolutely not. Don't even think about it. Our license plates are expired plates and sold for collecting purposes only. It is illegal to attach expired license plates to a vehicle. Even if your state only requires one plate, it is illegal to attach another license plate. If you need license plates for a vehicle, contact your local Department of Motor Vehicles. We do not sell plates to people who order only current style plates from the state they live in. Sorry. See similar questions...