Yes to both, but the panel would need to be mounted onto a special frame and extra piping may be needed. There would be an additional cost, which the installer will discuss with you.

Fitted Sheet: Also known as the bottom sheet, fitted sheets typically feature gusset corners with elastic sewn around the bottom edge to fit around and hug the mattress. Flat Sheet: Also known as the top sheet, the flat sheet is placed on top of the fitted sheet and tucked around the bottom and sides of the mattress

We recommend a light-colored, thermoplastic membrane for almost all flat or low-sloped roofs, whether a small porch roof or a large commercial building. "Thermoplastic" means that the membrane is heat-welded together at the seams, providing an almost monolithic roof covering, assuming the those welds are held to high quality-control standards. Some other roof membranes rely on adhesives or tapes for bonding at the seams, which tend to fail over time.

The solar panels need to face in a southerly direction (ideally somewhere between southeast and southwest), and ideally they should be fitted on a sloping roof.

The two most popular roof designs for a barn are Gable and RCA (Raised Center Aisle). They are both very functional, with the gable being less expensive due to the material savings and ease of installation. The RCA, while costing a little more, has at least three important advantages: The raised center aisle design has a very pleasing esthetic effect and pretty well defines the use as a home for horses rather than just another building.

There is no one roof system that is best for all applications. Keep in mind that even if you are using the best materials, your roof system still can be installed improperly and you could end up with a leaky roof. Good workmanship and proper attention to detail (e.g., flashing and drainage issues) are just as important as material selection. Also, maintenance plays an important role in roof system integrity and service life.

No, for those patients that prefer a fuller buttock with a body lift, the redundant skin and fat that would normally be cut away around the waist can be used to enhance buttock fullness. Fat grafting can also be performed.

You should remove ALL of the curved portions of the lens. Any curved portion that remains will act like part of a lens. 10 to 20 strokes with sand paper is all it should take.

A Galvalume? SSR is an ideal system for retrofit roofing. Its light weight makes it suitable for retrofit applications over any old, leaking, conventional, nonmetallic roof system. Retrofitting is accomplished by installing to the existing roof structure a light weight sub-framing system, generally made with light structural steel sections, that provides a minimum ?:12 slope for the new Galvalume? SSR.

Yes, any flat roof is suitable for an EPDM covering, so long as the roof can be walked upon. Structurs such as prefabricated corrugated roof garages are not suitable.

Eventually (after many years) your roof will start leaking. If it is just a small leak here or there, you can easily patch the roof; but time does take its toll. If the time does come, you can just rip off the existing leaves and replace them with new leaves. You want to do all you can when constructing the roof to expand the life of the roof.

There are a number of brush-applied, liquid roof coatings available through your local branch, which provide waterproof protection to most conventional roofing surfaces. Contact your local branch for further details.

Based on construction industry experience estimates, life expectancy ranges from 5 years to 30 years dependent on the actual waterproofing membrane used, although with good care and annual maintenance it should last in excess of this.

Flat roof greenhouses use water porous coverings so the rain will pass through. The rain will tend to drip through in a rectangular grid pattern so the grower will need to determine whether it is better to leave the roof closed during a rain or retract it.

More and more people are wanting light in their homes and with a flat roof extention this is still possible. Taking off the existing flat roof and installing a new low pitch lean to can be done using our Global 600 range which is designed to go down to 2.5 degrees or a square or rectangled hole can be made into the roof and a lantern or roof light can be installed to sit over the hole to let light in. Lantern of roof lights are becoming more popular.

Home | Applications | FAQ | Warranty Details | Technical Info | Resources | Bookmark Site | Enquiry Form | Contact DieselOnGas.com is a website built to provide information for a variety of products and services associated with fuel burning engines. nor does AET make any representations regarding the use or the results obtained with the information. In no event shall AET, its employees or associates be liable to any person or individual for any loss or

This is when we extend the ridge line of a hip-end roof to make it into a gable-end roof. This gives you a much larger loft area. A hip to gable extends the ridge line from the existing hips to overall the flank wall of the house. It will effectively add on the required space to enable the staircase and the shower-room to be built and also increase the standing space available in the loft.

A gable attic fan is a fan that is mounted in your attic on an exterior gable end wall. This fan pulls heat out of your attic just like an attic fan. A shutter will have to be installed so air can be removed from your attic.