Fill your log splitter hydraulic fluid reservoir approximately 1" below the reservoir tank fill hole. This should be at least five gallons of fluid on 22, 26, and 34 Ton models and at least seven gallons for the 34-ton Deluxe model. Dextron 2, Dextron 3, or Universal Hydraulic Oil is recommended for all Swisher log splitters.

Dirt in any system (air, electric, or hydraulic) will cause wear. Air tools suffer most from dirt because the compressor is sucking in dirt all the time and tool exhaust ports allow dirt to get into the tool. Since the hydraulic system is a sealed system, dirt gets in only by carelessness. And, to protect against this, the hydraulic system has a full-flow filter.

The performance of the entire aircraft hydraulic system can be affected by the condition of the hydraulic fluid. If the hydraulic fluid additives are damaged or depleted, the hydraulic fluid may no longer perform adequately in the system. Only after sampling the hydraulic fluid for the purpose of fluid analysis can one determine the condition of the additives. This allows action to be taken before damage to the hydraulic system can occur.

Routine Sampling - Each system should be sampled at least once a year or every 3000 flight hours, or whenever the airframe manufacturer suggests. Suspicion of Contamination - If contamination is suspected, fluids should be drained and replaced, with samples taken before and after the maintenance procedure.

A: Your jack plate’s hydraulic pump takes 20 weight (20w-20) non-detergent motor oil or a light weight hydraulic oil.

Your log splitter has a limited two-year warranty handled by Swisher Mower & Machine Co. Inc. The engine warranty is also two years handled by the engine manufacture. If you have an engine related issue please contact Briggs and Stratton at 1-800-233-3723.

In laboratory tests, concentrations of up to 5% Skydrol in jet fuel were cooled to -30oF. No gel formation or any other effect was observed. 5% is the maximum concentration possible in the worst case of a leak in a fuel tank heat exchanger.

Your new baler will not be shipped with hydraulic fluid in the tank. Your Pre-Start Up Manual will provide the correct number of gallons of hydraulic fluid and a list of suggested fluid manufacturers. The hydraulic fluid needs to be located at the installation site upon the arrival of the equipment so that the installation contractor or dealer’s installer can add the fluid into the tank prior to start-up.

The fluid is a light inert oil. It has a very low viscosity and moves freely inside the containment tube.

We use glycerin, FDA approved. This food additive is found in many recipes, the most common being frosting (or icing) on cakes. It is also used in some skin creams, makeup and lipstick. Others use animal-based Glycerin or water combinations.

For a given input power, a two-way splitter will typically decreases output by 3.5 db, three-way by 5.3 db and four-way by 7.5 db.

A hydraulic lift is the least expensive of the two to purchase and install. It can be used with loads from 1000 to 6000 lbs. It has a maximum carriage size of 10 ft. x 10 ft. or maximum vertical lift of 22 ft. and the capacity to stop at two levels. A mechanical lift is used where larger carriages are needed, where a vertical rise greater than 22 ft. is required, or where the capacity to stop at three or more levels is required.

Our cabins are all cut from pine timber. The walls come in a choice three thicknesses 1.5 inches, 2 inches or 2.5 inches (38mm, 50mm or 64mm).

The hydraulic fluid you can use is any hydraulic fluid that is kept on the shelf of major automotive stores. The fluid we use is Citgo brand AW32 hydraulic oil also used in farming and agricultural applications, or any tractor hydraulic fluid will work.

Yes, but it is used only for a crude estimate of acid number, and not a precise numerical value. The Skydrol Test Kit is available from TBM Corporation, 314-721-5590, and other Skydrol distributors.

Consult with your supplier or review the product technical data sheet to see if the fluid properties include high VI (>150) in combination with good shear stability. Most suppliers offer high quality fluids that will provide some or all of the critical MEHF features. The MEHF performance level does not conflict with other OEM specifications or regional standards.

APPROXIMATELY ONE GALLON. THE POWER PUMP’S FLOW RATE IS APPROXIMATELY .75 GALLON PER MINUTE OF HYDRAULIC FLUID.