Yes. SELECT customers may have up to four computers connected simultaneously. However, CLASSIC customers may only have one computer connected to the network at a time. Yes, with Choice OnLine you can surf the Net and simultaneously make phone calls or watch TV. To use a fax machine or dial-up modem while surfing the Net, you must have a normal phone line available. Your computer will not allow you to use our Choice OnLine service and dial-up to another Internet service simultaneously.

The HP Advancestack 100Base-T Hub-8txe and the ProCurve Networking by HP 100Base-T Hub 8 can only be directly connected to another Class II 100Base-T hub or to a switch. To connect them to a 10Base-T hub, either use a switch in between, or connect them to the ProCurve Networking by HP 10/100 Hub 12 or 12m or ProCurve Networking by HP 10/100 Hub 24 or 24m which are both Class II hubs that autosense the speed of each port to be either 10Mbps or 100Mbps.

Ethernet hubs can be purchased at your local computer store. AT&T does not provide installation support for Ethernet hubs.

PC/104 systems with multiple processors or peripherals that have Ethernet interfaces can use a PC/104 Ethernet switch or hub board to be networked together. Fast Ethernet and 10BaseT switches or hubs are available with auto-MDI-MDIX network installation and up to five auto-configurable 10/100 transceiver ports. Ethernet connections are made through either onboard RJ-45 jacks or via right-angle Molex connectors that can be used to mount RJ-45 jacks in a faceplate, endcap or enclosure.

Yes, you can connect the player directly to your computer using an Ethernet crossover cable. You can purchase a crossover cable at most retail computer stores. Once you have this connection, you'll need to set up your network adaptor and Squeezebox with static IP addresses so that they can find each other.

A hub is a network device that extends the network so that you could connect more than one computer to the network jack. A network hub can be borrowed from the ITS department. Verify if your hub has a button called Normal/uplink near the rightmost end. It is not necessary that your hub should have the Normal/uplink button. If you see the button, make sure you press the button inwards to set it to uplink.

A switch has chips to store MAC addresses of the connected clients. Hubs do not. Therefore a switch can send packets directly to the intended computer based upon the header of the packets. Hub is different, when hub receives packets, it will broadcast packets to all the clients that are connected and that costs traffic. A switch is more efficient than a hub.

Yes, all you have to do is to obtain an IP address from your network administrator and follow the instructions in the installation guide.

Yes the SQ2020 2F8, SQ2040 2F16 and the SQ2040 4F16 have inbuilt Ethernet connection. For the SQ2020 1F8 we supply a serial RS232, Ethernet converter kit (SQ20A801) a power adaptor lead is included with the kit to power the modem and the Squirrel from the mains power pack (MPU-12V)

No, because Ethernet switches and hubs need Ethernet data. They would also add a lot of latency (or delay) to a Pro16 system. For parallel (or "star") connections, use the A-16D or A-16D Pro A-Net Distributor. Links:

No. An EthIR Beam receives infrared frames from an infrared device and delivers these to the EthIR Switch. The EthIR Switch then translates these infrared frames to Ethernet frames (and vice-versa) forwarding and receiving frames to and from an Ethernet network. An Ethernet hub cannot translate infrared frames. That is the purpose of the EthIR Switch.

Only the computer which has been registered with ResNet will be able to access the network outside your room. The remaining computers will not be able to communicate with resources outside your residence hall. Using a hub or switch can potentially cause your port to stop responding to all traffic.

Add an HP J3231A Remote 2C/HP Internet Router Bundle to your workgroup. This product has a 10Base-T port that will connect to the Switch Link port on the Hub-12txm or Hub-12tx.

Halleck Undergraduate Bistro, also known as The HUB, is located adjacent to the Cafeteria in Halleck Student Center. The HUB offers students a relaxing atmosphere in which they can enjoy a variety of sandwiches, salads, beverages, snacks, "Sub Connection" subs, "Freshens" frozen fruit smoothies and ice creams, and "Pretzel Logic" gourmet soft pretzels.

Yes, the OneTouch USB Cable can be used with a hub, rather than connected directly into a port on the computer. With the 9-pin serial cable, just plug it into your meter and the serial port (COM port) of your computer. You may need to restart your computer if another device had been using the serial port. With the OneTouch USB Cable, you must install a software driver before using it for the first time.

Good question. According to the USB spec, software is required to connect not only to first tier devices, but also to any plugged into USB hubs. It appears that there is a bug in the Kodak Mounter and USB connection software causing it to fail unless the camera is "device #0", connected directly to the computer.

C.6. I'm running Acorn Access. Is there any way I can share files over a serial link? I have SLIP set up, and I can ping one machine from the other with no problems, but I can't see its disks.

A hub and switch are two devices that split the bandwidth coming from any ethernet device that is connected to them they will not route communications from your LAN to the internet. All they do is split the bandwidth so your modem can see all of the MAC addresses connected to it so it will only give a connection to one of those devices.

No. The Hitch will recognize the hub connect to the first device it finds on the USB hub. If that device is unplugged from the hub, the Hitch will then search for another device connected to that hub, but will never connect to more than two devices at once. No. The Hitch is a bridge device, and contains no memory. This is an advantage because it cannot have any issues with storage, such as hard-disk failures or memory allocation errors. No.