Before inserting your USB memory stick, please log in to the machine directly (not via SSH from another system). Logging in at the console will ensure that the USB memory device is mounted with you as the owner. It is safest to insert the device into one of the USB ports on the front of the computer (rather than those on the back or on the keyboard).

The exact error message looks like Could not find USB device (vendor 0x0000, product 0x0000). Make sure this device is connected to the computer You have to set up the permissions on your USB device correctly. See Section 4.3, "Setting up permissions for USB ports".

It is generally possible to use modern, USB-based memory sticks under Linux; however, not all USB memory sticks will work on our systems. Most USB memory stick devices produced since 2003 will work, while older devices are less likely to be supported. In general, the older the device, the less chance that it will work. The only way to know for sure is to try to use it. We do not provide any kind of card reader on any of the machines.

You can go 5 meters or around 16 feet from a computers USB port or from a powered USB hub to a USB device. Back To Questions

The requirement is similar to that of USB 1.1, but all components will have to be USB 2.0 compliant. A successful USB...

Windows 98 default supports only USB 1.1. Install a USB 2.0 PCI adapter then USB 2.0 device still can work fine in Windows 98. Some device such as Micronet´s USB 2.0 adapter, it includes a USB 2.0 driver written by third party so it can work in Windows 98SE.

Solaris supports Digi InsideOut Networks' devices and recently, KeySpan and Prolific chipset based devices' support were also integrated to Solaris. Keyspan and Prolific USB serial drivers are available in Solaris Express dated 2/2006 and in Solaris 10 Update 2 and later. PL2303 chip based adapters and Keyspan USA-19HS adapter are available as part of Solaris 10 Update 2. Keyspan USA-49WLC adapter is supported in Solaris Express dated 3/2006 and will be available in Solaris 10 update 3.

Not only will it not work, you may damage your device. In order for a device to work with USB it must be compatible and have appropriate drivers. Some early releases of the Freestyle Pro and Precision Pro were not USB compatible; if it did not come with an adapter you are out of luck.

The exact message looks like *** Error ('Could not claim the USB device') *** Could not claim interface 0 (Operation not permitted). Make sure no other program or kernel module (e.g. dc2xx or stv680) is using the device and you have read/write access to the device. You have to make sure that no such kernel module is loaded and that you have set up the permissions on your USB device correctly, such that you have (non-root) write access to the camera device.

No, according to policy you cannot use any type of removable media to bring it or take out software/files. Please, contact Steven Graham so that software can be made available on the systems.

It might seem that the USB device is fairly slow, especially when writing to the device. This is for two reasons: Firstly, USB devices are substantially slower than hard drives or other high-speed media; furthermore, larger-capacity flash memory devices are often slower for write access than low-capacity devices. Secondly, we mount the device in "synchronous" mode, which makes writes seem slower than the more common "asynchronous" mode.

Yes, but only Prolific based devices connected to an uhci controller are supported (ohci and ehci are not supported). this time, there are no secure USB commands to transfer data to or from a USB mass storage device. If you are concerned about USB security, please add the following lines to the file /etc/system exclude: drv/scsa2usb

You can either manually configure /etc/conf.modules (or /etc/modules.conf with 2.4-ready versions of modutils) to load the modules you require like this; alias usb uhci post-install uhci modprobe printer post-install printer modprobe joydev post-install joydev modprobe hid This makes sure the modules I need for my joystick and printer are loaded, if you modify your system startup to "modprobe usb".

Foxmail uses the absolute path ONLY for accounts(mailboxes) located in the folder selected by the user... If you create your accounts in the default location (\mail), Foxmail could be used from any logical drive (like on USB drives wich can have different drive letters allocated in each different computer) without any problems arising while doing so.

If the computer lab is full or is in use for a class, you can use one of the 15 laptop computers available for 2-hour checkout at Team55. Printers for the laptop computers around the library are located on each floor.

Add a new idea by using the Add New Idea Form. You must complete an Idea Form with all of the information about your idea and save it to the database. After you save it, it will be available for view on the Idea Journal page. You should review all of the information in the Idea Lab related to building your idea and taking action on your idea. You should then find a mentor who has experience with ideas like your and request that they review your idea to find out how you can take action on it.]

Close all the files accessed from the USB Device. Click the green icon on the system tray. Click on "Stop USB Mass Storage Device" A window would appear "The USB Mass Storage Device device can now be safely removed from the system." Click "OK" and then unplug the USB Device. Note: The green icon do not appear on Windows 98SE Operating System. Just make sure no files are open and then remove the USB Device.

Under certain circumstances the T8 will fail to recongize a USB device which is attached to the T8 before turning ON the T8. As a workaround, try turning ON the T8 first, then attaching the problematic USB device. This may allow the T8 to recognize the device properly.