Why do you recommend the Via-jet (R) over the Water Pik (R)?
Frequently Asked QuestionsFirst, I have owned both and both are good products. Colgate originally owned the rights to the Via-jet (R). The Via-jet (R) comes with a lid to keep dust out of the reservoir while not in use, and also comes with both the standard and sulcus tips (2 each). Finally, the Water Pik (R) model has changed and our cannulae adapters no longer fit the newer model so we no longer sell it. The ViaJet has recently been revised and is available now as the Viajet PRO (Sept. 2002).
Which whirlpool system is better ? air or water one ?
FREQUENTLY ASKED QUESTIONS - FAQrelaxes our muscles and joints Depending on individual needs, one should consider the advantages of both massage systems. The best is to choose the MIX option which combines the advantages of both systems.
Can I re-cycle the water from a water jet machine?
Fortron UK - Frequently Asked QuestionsSorry No, the waterjet head always requires clean pure water. It can only be used in the catcher tank to raise & lower the water level.
Can jet milling systems be automated?
Jet Milling Equipment FAQs by The Jet Pulverizer Co.Yes, but our mills are so simple to operate that very few people bother. But, the control system in a loss-in-weight feeder may be used to trigger a shut down of the mill in case there is no feed, and a pressure sensor could be installed to shut down the mill if there is not enough air. These are the key parameters to monitor.
How does water jet cutting work?
Water Jet - Waterjet Machine Manufacturing FAQ'sThere are two main steps involved in the waterjet cutting process. First, the ultra-high pressure pump or intensifier pressurizes water to pressure levels above 40,000 psi (2760 bar); to produce the energy required for cutting. Second, water is then focused through a small precious stone orifice to form an intense cutting stream. The stream moves at a velocity of up to 2.5 times the speed of sound, depending on how the water pressure is exerted.
What are loads?
DCB | | Resident Indians | Mutual Funds | FaqLoad is a charge collected by a mutual fund when it sells units. It can be levied as an entry load (i.e., the charge is collected when an investor buys the units) and as an exit load (i.e, the charge is collected when the investor sells back the units).
what size customer loads do micro-SMES systems provide the best solution?
SMES FAQCustomer loads in the 1MW to 10 MW range are normally supported by micro-SMES systems. In some cases, loads as small as 500kVA provide economic conditions suited to a micro-SMES solution. ASC's application engineers will work with you to determine the optimum solution for your site.
Are there not loads of systems like this on the Internet already? What makes Chamber Trade unique?
Chamber Trade - trade offers leads company agent FAQYes, there are plenty of market places on the Internet. However, the following aspects, combined together, make Chamber Trade unique: the companies publish their own business inquiries and search the database themselves, without intermediate links
Are there any tweaks for systems that will need to support large loads?
m0n0wall HandbookYou may need to up the kern.ipc.nmbclusters sysctl. If you are getting "out of mbuf" errors, this will fix that. kern.ipc.nmbclusters may be adjusted to increase the number of network mbufs the system is willing to allocate. Each cluster represents approx- imately 2K of memory, so a value of 1024 represents 2M of kernel memory reserved for network buffers. You can do a simple calculation to figure out how many you need.
There is no water flowing through my Dental Water Jet upon the first use, what do I do?
Waterpik - Frequently Asked QuestionsIf you are not receiving any water flow through your Dental Water Jet please try the following steps: Try turning up the water pressure on the handle. If this is a new purchase, the unit will need to be primed before use. Please refer to your instruction manual for priming instructions.
My jet craft runs very well in shallow water but seems sluggish in the deep stretches of water, why?
SnyderBoats.comThere a simple answer, it is just a bit wordy. There are basically two types of hulls, Displacement Hulls and Planing Hulls. Displacement hulls are designed for big water applications. They cut through the water with an extreme degree of angle in the bow, pushing the water to port and starboard. In rough seas, the idea is not to plane, but to push through the water. Planing hulls are designed to lift and ride on the surface of the water.
What is Microbial Contamination?
FAQThere are at least 27 separate species of microbes - bacteria, yeast and fungus that can exist in and feed on crude oil (and it's products). These oil eating micro-organisms have a natural affinity with petroleum based products because they actually produced crude oil by decomposing billions of tons of ancient forests and animals. Subsequently when crude oil is extracted from the ground it has a resident microbial population - fortunately this is killed off during the refining process.
How do the jets and jet systems allow me to customize my hydrotherapy experience?
Spa Deck, Hot Tub Plan - Sundancespas.comMany jets are adjustable, giving you an amazing number of options. The Fluidix ST jets on many Sundance Spas models adjust from oscillating to targeted. The Fluidix Intelli-Jets (selected models) rotate clockwise, counter-clockwise, or stationary. You can control the flow, volume, and movement of other jets as well. In addition, controlling the amount of air mixed with the water with the air control valves changes the dynamics of the massage.
Are there other means of treatment?
Thyroid.org: Thyroid Surgery FAQSurgery is definitely required for a diagnosis of thyroid cancer or the possibility of thyroid cancer (see Thyroid Cancer brochure). In the absence of a possibility of thyroid cancer, there may be non-surgical options of therapy. You should discuss other options for therapy with your physician.
What is a Jet ?
Frequently Asked QuestionsA Jet is the smooth uniform flow of air a wind tunnel produces. In a VWT it is often called a wind column. The Jet is the Flight Area of a Vertical Wind Tunnel.
How many public water systems are there in the United States?
EPA Ground Water & Drinking Water Frequently Asked Quest...There are almost 170,000 public water systems in the United States. Visit EPA's page of water system facts and figures for more information.
Are Multi-Pure Drinking Water Systems certified to reduce contaminants of health concern?
Frequently Asked Questions - Drinking Water System - Carbon ...Multi-Pure's Drinking Water Systems have been tested and listed under NSF/ANSI Standard No. 42 and Standard No. 53 by NSF International. The replacement filters are also tested and certified by NSF.
What contaminants are Multi-Pure Drinking Water Systems certified by NSF to reduce?
Frequently Asked Questions - Drinking Water System - Carbon ...Multi-Pure Drinking Water Systems have been tested and certified by NSF for the reduction of the following contaminants/substances (*99% is the maximum rate of reduction certified): Multi-Pure Drinking Water Systems have been certified or registered by the states of California, Iowa, Wisconsin, Massachusetts, and Colorado (all the states that regulate drinking water systems).
How expensive are water treatment systems?
Long Island Water Services: Commercial Water Purification Se...A state-of-the-art water treatment system from EcoWater Systems will pay for itself. Conditioned water helps your water heater run more efficiently, reducing energy bills. It requires less detergent to wash clothes and it’s easy on your pipes, fixtures and water-using appliances. Treated water can even brew a pot of coffee using fewer coffee grounds. And drinking water produced by a reverse osmosis (RO) filtration system is far more economical than the cheapest bottled water.
