The fuel-oil mixture ratio for all Poulan two-cycle products is 40:1. You can obtain this ratio by mixing 3.2 oz. of oil with one gallon of regular gas. If you have other brands of equipment that require different fuel/oil ratios and you don't want to mix separate fuel cans, you should use the lowest numerical ratio. For example, if you have products requiring 40:1, 50:1, and 32:1 ratios you should use the 32:1 ratio for all products.

Mix 3.2 ounces of Poulan 2-cycle air cooled engine oil to one gallon of fresh unleaded gasoline to obtain the recommended 40:1 fuel to oil ratio. Over a period of time oil will separate from gasoline. To properly insure oil and gas mixture,we recommend thoroughly shaking your oil and gas mixture before refueling your unit. Back to Top >> See similar questions...

For our Zenoah-powered boats, we recommend a 20:1 or 25:1 mixture of a quality 2 cycle synthetic oil. Zenoah recommends 90 or higher octane unleaded fuel (although we have quite a few customers who have had success with 87-89 octane). We recommend a mixture of 25:1 (5 oz of oil to 1 gal of gas) or 20:1 (6 oz of oil). Either will work for you, but you should pick one mixture and not change. The oil needs to be a good 2 stroke synthetic. We recommend AMSOIL. See similar questions...

With the exception of our outboards which have oil injection systems, Tohatsu 2-stroke outboards require a 50:1 (2.5 ounces of oil for each gallon of gas) oil/gas mixture after the initial break-in period. Tohatsu outboards which have oil injection will automatically mix the correct amount of oil and gas depending on the engine requirements; you don't have to pre-mix your oil & gas with these systems. We've put together a handy chart to help you calculate the amount of oil/gas to mix. See similar questions...

With the exception of our outboards which have oil injection systems, Nissan 2-stroke outboards require a 50:1 (2.5 ounces of oil for each gallon of gas) oil/gas mixture after the initial break-in period. Nissan outboards which have oil injection will automatically mix the correct amount of oil and gas depending on the engine requirements; you don't have to pre-mix your oil & gas with these systems. We've put together a handy chart to help you calculate the amount of oil/gas to mix. See similar questions...

NBB maintains the largest library of Bioheat® fuel and Biodiesel information in the world. Most questions can be answered through a review of the information on the National Biodiesel Board website located www.biodiesel.org. If further information is desired, you can email your question to the NBB at info@biodiesel.org. See similar questions...

Not here at java.sun.com, but the independent site Java Sound Resources provides the Java Sound Programmers' FAQ. Unless otherwise licensed, code in all technical manuals herein (including articles, FAQs, samples) is provided under this License. See similar questions...

Sixty years ago, the government wanted a pool of trained radio operators and electronics technicians to draw from in case of another World War. They used the ham radio exams to achieve this goal. With the advent of digital communications, the military no longer uses Morse code, so training radio operators is much easier. And they now repair radios the same way everyone else does — throw the thing away and get a new one. However, the FCC exams have not kept up with these changes. See similar questions...

Of course (although we cannot promise to answer every inquiry). E-mail our Help Department at help@atpm.com. See similar questions...

where the optional address is your email address. If you do not provide an address, the return address of the email you send to majordomo is used. where the optional address is your email address. If you do not provide an address, the return address of the email you send to majordomo is used. See similar questions...

All known oil tanks and systems are compatible with Bioheat® fuel at blends of 20% or less. For higher biodiesel blends, up to and including 100% biodiesel, compatibility will depend on the materials (metals, plastics, and rubber parts) in your tanks, pumps and fuel lines. For blends higher than 20% biodiesel only steel, mild steel, stainless steel, aluminum, fluorinated polyethylene fluorinated polypropylene and fiberglass vessels are recommended. See similar questions...

A.If riding your own bike it must be full of fuel on arrival so we can get an early start on day one. We use unleaded on tour and fill from our support vehicle. Two stroke riders will need to supply own oil, which will be carried on the support vehicle. You should also carry a 500ml spare in your pack just in case. See similar questions...

There are three possible answers here. Please note that you MUST use the correct fuel mix for your motor or you will ruin it. The fuel mix MUST be fresh. As a rule of thumb a seagull can use more but not less oil. Most British Seagulls use this ratio. If you have a pre 1979 engine, the fuel mix will be 10:1 UNLESS it was converted to run on 25:1. Newer 1979 and newer seagulls with black thumb lever throttles and black carb bodies use the 25:1 mix. See similar questions...

With the exception of our outboards which have oil injection systems, Tohatsu 2-stroke outboards require a 50:1 (2.5 ounces of oil for each gallon of gas) oil/gas mixture after the initial break-in period. Tohatsu outboards which have oil injection will automatically mix the correct amount of oil and gas depending on the engine requirements; you don't have to pre-mix your oil & gas with these systems. We've put together a handy chart to help you calculate the amount of oil/gas to mix. See similar questions...

Each two component kit is premeasured for correct ratio; however mix ratio's are also printed on the container. See similar questions...

The ratio of cement, sand and stone chips or gravel in the raw material mix determines the properties of hollow concrete blocks. A ratio of 1:3:6 [cement : sand: stone chips] confers higher strength, while a ratio 1:5:6 can be employed for normal load bearing construction. The water to cement ratio is usually 0.4:1, which is a little less than half the amount of water to cement. See similar questions...

this time the emergence of Bioheat® fuel is much too new for burner manufacturers to comment on. However, in work accomplished throughout the northeast, organizations like Carlin, Beckett and Power Flame (notable burner manufactures) all are reviewing Bioheat® fuel. Bioheat® fuel appears to have little or no negative impact on a burner’s performance while providing emissions, sulfur, lubricity, global warming and health benefits. See similar questions...