I generally don't repaint metal or refinish wood for a number of reasons. The main reason is that it's not original anymore. If it only has a few minor scratches or scuffs, it's better to leave it alone. Painting metal with a paint can or sprayer just doesn't cut it as the paint is going to come off. If I do paint something, it will be powder coated at a local factory and heated to 500 degrees. Same thing with wood. Most are simulated or veneers and if they have normal wear, I leave them alone.

We do not recommend refinishing an older ski. If the ski has been badly damaged or neglected we don't recommend using it. If you intend on using it, you can touch up the spots where bare wood is exposed by lightly sanding the spot and applying an exterior urethane based product, isolating the bad spots with masking tape. We have found that refinishing a ski makes it thinner, more flexible, and more likely to break. Old skis are already more brittle than their newer counterparts.

Assuming the wood was thick enough when originally installed, refinish no more than 2 time as the wood will be too thin. Home | About Us | Wood Selection | Wood Finishes | Installation | Frequent Questions | Links | Contact Us

No. It is not that I cannot refinish furniture, rather I chose not to. Everybody is not great at everything, so stick to what I do best.

Yes, you can paint it just like you did the hull and deck, it is made of fiberglass. If it is an older model, then you can remove the splash rail because it is screwed down rather than riveted like the newer models with will make it easier to remove and paint. - Tom Whitehurst I've repainted a few of the light blue ones with white spray paint and it worked great. I found them to be very porous and soaked up the spray paint.

Stucco (acrylic or cementitious) is adhered directly to the foam. Wood, plastic or metal cladding is mechanically fastened to the imbedded plastic ties. Stone and brick are attached according to design specifications.

Call 578-3186 to report a lighting problem. Please be as specific as possible. Include the number on the pole if possible. Most exterior lighting problems are repaired within two business days.

A standard sized bathtub, in reasonable condition, takes only 4 to 6 hours to refinish. The tub will typically be ready to use within 24 hours or even sooner with special curing procedures.

Unfortunately, we do not offer the repainting service on kayaks. During the manufacturing process of composite kayaks, the first step consists in applying gelcoat, which is done directly in the mould. If you apply gelcoat on your kayak to make it look better, its weight will increase by 7 pounds; furthermore, the result would be an "orange peel" finish. To obtain a glossy finish, it would be necessary to sand your kayak many times, which would be a very long and expensive process.

Interior pieces like dash vents, dash trim, and others can be painted. you must take special care in prepping and cleaning the surfaces before painting. Go to a shop and see if they carry special interior paint. This paint is specifically designed to paint and adhere to interior plastic pieces. It's always best to remove the part you plan to paint from the car before painting.

A leased car doesn't belong to you, it belongs to the leasing company. Therefore, you cannot make modifications and install custom equipment that alters the car. If you do, you'll likely be charged for the cost of repairs to undo what you've done.

Miracle Method is the largest, most experienced refinishing company in America. With over 100 offices, Miracle Method has been the leader in refinishing techniques and technology for over 25 years. Each franchisee receives extensive training and continuing education to ensure that each and every customer receives the very best quality and service available.

It really depends on the size of the job, however the average size job (800-1000 sq ft) usually takes us 2 days to complete.

average’ sized home in Vancouver usually consists of a living room, dining room a couple of bedrooms and a hallway and entrance. If the floors don’t need any repairs and you’re not staining them, we can usually refinish the floors in 3 days. The first day is the longest. If things go well we usually can have the first coat on at the end of the day. The next two days we apply the second and third coats of finish.

A Yes, with the new finishes available, in many cases we recommend that you let us strip and condition the piece ready for you to finish.

However, we can do a blend so the new area does not seem obvious. Matching the exact shine is also not

Usually we will need four to six weeks to refinish your furniture whether it is a single piece of and entire bedroom or dining room outfit. Special arraignments can, sometimes, be made to expedite work but we cannot rush drying times.

Maybe you're tired of dealing with peeling paint and rotting clapboards. And you wonder, "Will another coat of paint really hide the weather-worn condition of my wood siding? And even if it can, is it worth the cost?" Or maybe you're thinking about replacing warped hardboard siding...or getting rid of dated asphalt or asbestos siding...or eliminating dented metal siding...or giving a fresh, contemporary look to masonry walls.

Vinyl siding is one of the most versatile exterior design products you can work with. Alside, for example, offers many different vinyl siding lines. That broad selection lets you choose among a wide variety of design options, including horizontal and vertical siding; traditional clapboard and authentically detailed "shaped" sidings; wide and narrow panel exposures; smooth, subtle and deep wood grain textures; plus a wide assortment of traditional and contemporary colors.