You'll need a 3/8" wrench (preferably socket wrench) to assemble the bed. In addition, it is best to have an extra person available to assist. See similar questions...

Assembling a Solexx Greenhouse is takes just a few readily available tools. You will need a screwdriver, variable speed drill, sharp knife or utility knife, tape measure, step ladder, GE Silicon-2 caulk, caulking gun, clear PVC glue and a level. I am interested in your Solexx polycarbonate covering. How do you install it? Our specially formulated Solexx greenhouse panels are actually a polyethylene blend. See similar questions...

All you need is three tools to assemble you loft bed: 1) Ratchet wrench with ½ inch (13mm) socket. 2) Standard Phillips head screwdriver. 3) Rubber mallet (preferred) or hammer. A power drill/electric screwdriver with a Phillips See similar questions...

We provide a hardware pack in all of our units that include all the necessary tools to assemble the product. See similar questions...

You will need a size 2 cross head screwdriver for assembly. A mallet may also be useful to help push bungs home. Any allen keys, nuts and bolts required are supplied with your product. back to top See similar questions...

No. Standard and/or metric wrenches, standard and Phillips head screw drivers, and occasionally pliers are all that is required to assemble a Haulz-All. See similar questions...

All Bell'O? products include complete assembly instructions, and include all fasteners and tools needed. Average do-it-yourself skill is all that is required. See similar questions...

Assembly is only required for our beds. All our beds are supplied disassembled to minimize shipping costs. Each bed will come with written assembly instructions and a list of the tools (usually just a hammer and a 3/8 inch socket spanner for the Round Hill bed) required for assembly. Each part is numbered. Bamboo dowels are included to pin the joints together. See similar questions...

No tools are required to assemble the raised beds. However, to set the pins flush with the top of the planter, a hammer (or nearby rock) may be needed in order to pound the pins into very hard ground. More often, though, the pins can be pushed flush by hand, or left exposed a few inches for use with a shade cloth or greenhouse covering (see below). See similar questions...

NONE. No tools needed . We have designed our garage screen for simple installation. No long complicated instructions. It is easy as 1,2,3 GUARANTEED! No problem. Our screens were carefully designed to accommodate most standard door sizes. We designed our screens to be flexible enough to fit openings that may be a few inches shorter or narrower. See similar questions...

The only tools needed are a #3 Phillips screwdriver, and a rubber mallet, or a soft blow mallet. Assembly instructions can be found in the Support Document Section and with the specific dolly listing. See similar questions...

Unless this was agreed at the quotation stage, then all items needing dismantling are expected to be dismantled and ready to move prior to our arrival. If agreed at the quotation stage our staff will carry out dismantling and re-assembling to the best of their ability. It is essential that we know what is required at the quotation stage to allow for the necessary resources and equipment to be provided. See similar questions...

The Desk/Bed is an RTA (ready to assemble) furniture. If you assemble it at home, we recommend that two people assemble it, though one can assemble it by himself. See similar questions...

No. All the favors come just as they are shown with instructions and ribbon or raffia fully assembled. No assembly is required, and they are ready to give to your guests. See similar questions...

Let your RA or RD know that you need or would like the beds changed. Except in cases of emergency or health reasons, these requests will be met as time permits. Custodians and maintainers will take care of safety issues first, and are not permitted to bunk or de-bunk your beds without a work order. See similar questions...

Model #BP90 - Wagon Bed Pad: The BP90 is a wagon bed pad that's desiged to fit any 34" - 36" wagon. This is the only bed pad that will work with the steel wagons without wood sides. The BP90 will fit Wagon Model #'s 18, 22, 24, 28, 31, 32, 89 and 90. Model #BP24 - Wagon Bed Pad with Side Pads: The BP24 is a wagon bed pad and side pad set. This item will only work with 34" - 36" wagons with wood stake sides. The side pads have velcro straps that fasten to the wood stake sides of the wagon. See similar questions...

Answer: The minimum tool requirements are an electric drill, hand held sander, and circular saw. Small hand tools such as pliers, hammer, wrench will also be needed. More sophisticated tools such as a router, planer, chop saw, etc. will make the job go easier and faster but are not necessary. See similar questions...